Introducing The New!
Surepassexam Collection
Get Unlimited Access to all
Surepassexam's PREMIUM files
Q1. - (Topic 2)
Refer to the exhibit.
What two things can the technician determine by successfully pinging from this computer to the IP address 172.16.236.1? (Choose two)
A. The network card on the computer is functioning correctly.
B. The default static route on the gateway router is correctly configured.
C. The correct default gateway IP address is configured on the computer.
D. The device with the IP address 172.16.236.1 is reachable over the network.
E. The default gateway at 172.16.236.1 is able to forward packets to the internet.
Answer: A,D
Explanation:
The source and destination addresses are on the same network therefore, a default gateway is not necessary for communication between these two addresses.
Q2. - (Topic 1)
Refer to the exhibit.
A network device needs to be installed in the place of the icon labeled Network Device to accommodate a leased line attachment to the Internet. Which network device and interface configuration meets the minimum requirements for this installation?
A. a router with two Ethernet interfaces
B. a switch with two Ethernet interfaces
C. a router with one Ethernet and one serial interface
D. a switch with one Ethernet and one serial interface
E. a router with one Ethernet and one modem interface
Answer: C
Explanation:
Only a router can terminate a leased line attachment access circuit, and only a router can connect two different IP networks. Here, we will need a router with two interfaces, one serial connection for the line attachment and one Ethernet interface to connect to the switch on the LAN.
Q3. - (Topic 1)
Refer to the exhibit.
A network has been planned as shown. Which three statements accurately describe the areas and devices in the network plan? (Choose three.)
A. Network Device A is a switch.
B. Network Device B is a switch.
C. Network Device A is a hub.
D. Network Device B is a hub.
E. Area 1 contains a Layer 2 device.
F. Area 2 contains a Layer 2 device.
Answer: A,D,E
Explanation:
Switches use a separate collision domain for each port, so device A must be a switch. Hubs, however, place all ports in the same collision domain so device B is a hub. Switches reside in layer 2 while hubs are layer 1 devices.
Q4. - (Topic 3)
How many bits are contained in each field of an IPv6 address?
A. 24
B. 4
C. 8
D. 16
Answer: D
Explanation:
One of the key advantages IPv6 brings is the exponentially larger address space. The
following will outline the basic address architecture of IPv6. 128-bit-long addresses Represented in hexadecimal format: Uses CIDR principles: prefix/prefix length x:x:x:x:x:x:x:x, where x is a 16-bit hex field The last 64 bits are used for the interface ID http://www.cisco.com/en/US/technologies/tk648/tk872/technologies_white_paper0900aecd 8026003d.pdf
Q5. - (Topic 4)
What is the best practice when assigning IP addresses in a small office of six hosts?
A. Use a DHCP server that is located at the headquarters.
B. Use a DHCP server that is located at the branch office.
C. Assign the addresses by using the local CDP protocol.
D. Assign the addresses statically on each node.
Answer: D
Explanation:
Its best to use static addressing scheme where the number of systems is manageable rather than using a dynamic method such as DHCP as it is easy to operate and manage.
Q6. - (Topic 1)
At which layer of the OSI model does the protocol that provides the information that is displayed by the show cdp neighbors command operate?
A. application
B. transport
C. network
D. physical
E. data link
Answer: E
Explanation:
CDP is a device discovery protocol that runs over Layer 2 (the data link layer) on all Cisco-manufactured devices (routers, bridges, access servers, and switches) and allows network management applications to discover Cisco devices that are neighbors of already known devices. With CDP, network management applications can learn the device type and the Simple Network Management Protocol (SNMP) agent address of neighboring devices running lower-layer, transparent protocols. CDP allows devices to share basic configuration information without even configuring any protocol specific information and is enabled by default on all interfaces. CDP is a Datalink Protocol occurring at Layer 2 of the OSI model. CDP is not routable and can only go over to directly connected devices. CDP is enabled, by default, on all Cisco devices. CDP updates are generated as multicasts every 60 seconds with a hold-down period of 180 seconds for a missing neighbor. The no cdp run command globally disables CDP, while the no cdp enable command disables CDP on an interface. Use show cdp neighbors to list out your directly connected Cisco neighboring devices. Adding the detail parameter will display the layer-3 addressing configured on the neighbor.
Reference: http://computernetworkingnotes.com/cisco-devices-administration-and-configuration/cisco-discoveryprotocol.html
Q7. - (Topic 3)
An administrator must assign static IP addresses to the servers in a network. For network 192.168.20.24/29, the router is assigned the first usable host address while the sales server is given the last usable host address.
Which of the following should be entered into the IP properties box for the sales server?
A. IP address: 192.168.20.14 Subnet Mask: 255.255.255.248 Default Gateway: 192.168.20.9
B. IP address: 192.168.20.254 Subnet Mask: 255.255.255.0 Default Gateway: 192.168.20.1
C. IP address: 192.168.20.30 Subnet Mask: 255.255.255.248 Default Gateway: 192.168.20.25
D. IP address: 192.168.20.30 Subnet Mask: 255.255.255.240 Default Gateway: 192.168.20.17
E. IP address: 192.168.20.30 Subnet Mask: 255.255.255.240 Default Gateway: 192.168.20.25
Answer: C
Explanation:
With network 192.168.20.24/29 we have:
Increment: 8 (/29 = 255.255.255.248 = 11111000 for the last octet)
Network address: 192.168.20.24 (because 24 = 8 * 3)
Broadcast address: 192.168.20.31 (because 31 = 24 + 8 – 1)
Therefore the first usable IP address is 192.168.20.25 (assigned to the router) and the last usable IP address is 192.168.20.30 (assigned to the sales server). The IP address of the router is also the default gateway of the sales server.
Q8. - (Topic 3)
Which command can you use to manually assign a static IPV6 address to a router interface?
A. ipv6 address PREFIX_1::1/64
B. ipv6 autoconfig 2001:db8:2222:7272::72/64
C. ipv6 autoconfig
D. ipv6 address 2001:db8:2222:7272::72/64
Answer: D
Explanation:
An example of configuring IPv6 on an interface is shown below: Router(config)# interface fastethernet 0/1 Router(config-if)# ipv6 address 3000::2222:1/64
Q9. - (Topic 7)
Which route source code represents the routing protocol with a default administrative distance of 90 in the routing table?
A. S
B. E
C. D
D. R
E. O
Answer: C
Explanation:
SStatic EEGP DEIGRP RRIP OOSPF
Default Administrative distance of EIGRP protocol is 90 then answer is C
Default Distance Value TableThis table lists the administrative distance default values of the protocols that Cisco supports:
Route Source Default Distance Values
Connected interface 0 Static route 1 Enhanced Interior Gateway Routing Protocol (EIGRP) summary route 5 External Border Gateway Protocol (BGP) 20 Internal EIGRP 90 IGRP 100 OSPF 110 Intermediate System-to-Intermediate System (IS-IS) 115 Routing Information Protocol (RIP) 120 Exterior Gateway Protocol (EGP) 140 On Demand Routing (ODR) 160 External EIGRP 170 Internal BGP 200 Unknown* 255
Q10. - (Topic 3)
Which two of these statements are true of IPv6 address representation? (Choose two.)
A. There are four types of IPv6 addresses: unicast, multicast, anycast, and broadcast.
B. A single interface may be assigned multiple IPv6 addresses of any type.
C. Every IPv6 interface contains at least one loopback address.
D. The first 64 bits represent the dynamically created interface ID.
E. Leading zeros in an IPv6 16 bit hexadecimal field are mandatory.
Answer: B,C
Explanation:
A single interface may be assigned multiple addresses of any type (unicast, anycast,
multicast).
Every IPv6-enabled interface must contain at least one loopback and one link-local
address.
Optionally, every interface can have multiple unique local and global addresses.
IPv6 host addresses can be assigned in multiple ways:
Static configuration
Stateless autoconfiguration
DHCPv6
When IPv6 is used over Ethernet networks, the Ethernet MAC address can be used to
generate the 64-bit interface ID for the host. This is called the EUI-64 address.
Since MAC addresses use 48 bits, additional bits must be inserted to fill the 64 bits
required.
Reference:
http://www.cisco.com/en/US/technologies/tk648/tk872/technologies_white_paper0900aecd
8026003d.pdf
Q11. - (Topic 5)
What is the subnet broadcast address of the LAN connected to Router1?
A. 192.168.8.15
B. 192.168.8.31
C. 192.168.8.63
D. 192.168.8.127
Answer: A
Explanation:
The IP address assigned to FA0/1 is 192.168.8.9/29, making 192.168.8.15 the broadcast address.
Q12. - (Topic 3)
A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their common Ethernet link.
The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2. Based on the information in the graphic, what is the cause of this problem?
A. The OSPF area is not configured properly.
B. The priority on R1 should be set higher.
C. The cost on R1 should be set higher.
D. The hello and dead timers are not configured properly.
E. A backup designated router needs to be added to the network.
F. The OSPF process ID numbers must match.
Answer: D
Explanation:
In OSPF, the hello and dead intervals must match and here we can see the hello interval is set to 5 on R1 and 10 on R2. The dead interval is also set to 20 on R1 but it is 40 on R2.
Q13. - (Topic 3)
Which router command will configure an interface with the IP address 10.10.80.1/19?
A. router(config-if)# ip address 10.10.80.1/19
B. router(config-if)# ip address 10.10.80.1 255.255.0.0
C. router(config-if)# ip address 10.10.80.1 255.255.255.0
D. router(config-if)# ip address 10.10.80.1 255.255.224.0
E. router(config-if)# ip address 10.10.80.1 255.255.240.0
F. router(config-if)# ip address 10.10.80.1 255.255.255.240
Answer: D
Explanation:
255.255.224 equal /19 in CIDR format hence the answer
Q14. - (Topic 3)
Refer to the graphic.
R1 is unable to establish an OSPF neighbor relationship with R3. What are possible reasons for this problem? (Choose two.)
A. All of the routers need to be configured for backbone Area 1.
B. R1 and R2 are the DR and BDR, so OSPF will not establish neighbor adjacency with R3.
C. A static route has been configured from R1 to R3 and prevents the neighbor adjacency from being established.
D. The hello and dead interval timers are not set to the same values on R1 and R3.
E. EIGRP is also configured on these routers with a lower administrative distance.
F. R1 and R3 are configured in different areas.
Answer: D,F
Explanation:
This question is to examine the conditions for OSPF to create neighborhood.
So as to make the two routers become neighbors, each router must be matched with the
following items:
1.
The area ID and its types;
2.
Hello and failure time interval timer;
3.
OSPF Password (Optional);
Q15. - (Topic 7)
What is one requirement for interfaces to run IPv6?
A. An IPv6 address must be configured on the interface.
B. An IPv4 address must be configured.
C. Stateless autoconfiguration must be enabled after enabling IPv6 on the interface.
D. IPv6 must be enabled with the ipv6 enable command in global configuration mode.
Answer: A
Explanation: To use IPv6 on your router, you must, at a minimum, enable the protocol and assign IPv6 addresses to your interfaces.