Introducing The New!
Surepassexam Collection
Get Unlimited Access to all
Surepassexam's PREMIUM files
Q1. - (Topic 2)
Which address type does a switch use to make selective forwarding decisions?
A. Source IP address
B. Destination IP address
C. Source and destination IP address
D. Source MAC address
E. Destination MAC address
Answer: E
Explanation:
Switches analyze the destination MAC to make its forwarding decision since it is a layer 2 device. Routers use the destination IP address to make forwarding decisions.
Q2. - (Topic 3)
What does administrative distance refer to?
A. the cost of a link between two neighboring routers
B. the advertised cost to reach a network
C. the cost to reach a network that is administratively set
D. a measure of the trustworthiness of a routing information source
Answer: D
Reference: http://www.cisco.com/en/US/tech/tk365/technologies_tech_note09186a0080094195.shtml
Administrative distance is the feature that routers use in order to select the best path when there are two or more different routes to the same destination from two different routing protocols. Administrative distance defines the reliability of a routing protocol. Each routing protocol is prioritized in order of most to least reliable (believable) with the help of an administrative distance value.
Administrative distance is the first criterion that a router uses to determine which routing protocol to use if two protocols provide route information for the same destination. Administrative distance is a measure of the trustworthiness of the source of the routing information. The smaller the administrative distance value, the more reliable the protocol.
Q3. - (Topic 7)
Refer to the exhibit.
Which statement describes the effect of this configuration?
A. The VLAN 10 VTP configuration is displayed.
B. VLAN 10 spanning-tree output is displayed.
C. The VLAN 10 configuration is saved when the router exits VLAN configuration mode.
D. VLAN 10 is added to the VLAN database.
Answer: D
Q4. - (Topic 7)
Which destination IP address can a host use to send one message to multiple devices across different subnets?
A. 172.20.1.0
B. 127.0.0.1
C. 192.168.0.119
D. 239.255.0.1
Answer: D
Explanation: Multicast is a networking protocol where one host can send a message to a special multicast IP address and one or more network devices can listen for and receive
those messages. Multicast works by taking advantage of the existing IPv4 networking infrastructure, and it does so in something of a weird fashion. As you read, keep in mind that things are a little confusing because multicast was "shoe-horned" in to an existing technology. For the rest of this article, let's use the multicast IP address of 239.255.0.1. We'll not worry about port numbers yet, but make a mental note that they are used in multicast. We'll discuss that later.
Q5. - (Topic 5)
Which two of the following are true regarding the configuration of RouterA? (Choose two.)
A. At least 5 simultaneous remote connections are possible
B. Only telnet protocol connections to RouterA are supported C. Remote connections to RouterA using telnet will succeed
D. Console line connections will nevertime out due to inactivity
E. Since DHCP is not used on Fa0/1 there is not a need to use the NAT protocol
Answer: A,C
Q6. - (Topic 5)
The network administrator has found the following problem.
The remote networks 172.16.10.0, 172.16.20.0, and 172.16.30.0 are accessed through the Central router's serial 0/0 interface. No users are able to access 172.16.20.0. After reviewing the command output shown in the graphic, what is the most likely cause of the problem?
A. no gateway of last resort on Central
B. Central router's not receiving 172.16.20.0 update
C. incorrect static route for 172.16.20.0
D. 172.16.20.0 not located in Central's routing table
Answer: C
Explanation:
If we use 172.16.20.0 to route to 172.16.150.15, then the packet will route back. To clear this error we have to use.#no ip route 172.16.20.0 255.255.255.0 172.16.150.15
.command in configuration mode.
Q7. - (Topic 5)
What is the subnet broadcast address of the LAN connected to Router1?
A. 192.168.8.15
B. 192.168.8.31
C. 192.168.8.63
D. 192.168.8.127
Answer: A
Explanation:
The IP address assigned to FA0/1 is 192.168.8.9/29, making 192.168.8.15 the broadcast address.
Q8. - (Topic 3)
Which statements describe the routing protocol OSPF? (Choose three.)
A. It supports VLSM.
B. It is used to route between autonomous systems.
C. It confines network instability to one area of the network.
D. It increases routing overhead on the network.
E. It allows extensive control of routing updates.
F. It is simpler to configure than RIP v2.
Answer: A,C,E
Explanation:
Routing overhead is the amount of information needed to describe the changes in a dynamic network topology. All routers in an OSPF area have identical copies of the topology database and the topology database of one area is hidden from the rest of the areas to reduce routing overhead because fewer routing updates are sent and smaller routing trees are computed and maintained (allow extensive control of routing updates and confine network instability to one area of the network).