Introducing The New!
Surepassexam Collection
Get Unlimited Access to all
Surepassexam's PREMIUM files
Q1. - (Topic 3)
Given an IP address of 192.168.1.42 255.255.255.248, what is the subnet address?
A. 192.168.1.8/29
B. 192.168.1.32/27
C. 192.168.1.40/29
D. 192.168.1.16/28
E. 192.168.1.48/29
Answer: C
Explanation:
248 mask uses 5 bits (1111 1000)
42 IP in binary is (0010 1010)
The base subnet therefore is the lowest binary value that can be written without changing
the output of an AND operation of the subnet mask and IP...
1111 1000 AND
0010 1010 equals
0010 1000 - which is .40
/24 is standard class C mask.
Adding the 5 bits from the .248 mask gives /29
Q2. - (Topic 1)
A workstation has just resolved a browser URL to the IP address of a server. What protocol will the workstation now use to determine the destination MAC address to be placed into frames directed toward the server?
A. HTTP
B. DNS
C. DHCP
D. RARP
E. ARP
Answer: E
Explanation:
The RARP protocol is used to translate hardware interface addresses to protocol addresses. The RARP message format is very similar to the ARP format. When the booting computer sends the broadcast ARP request, it places its own hardware address in both the sending and receiving fields in the encapsulated ARP data packet. The RARP server will fill in the correct sending and receiving IP addresses in its response to the message. This way the booting computer will know its IP address when it gets the message from the RARP server
Q3. - (Topic 7)
Which statement about the inside interface configuration in a NAT deployment is true?
A. It is defined globally
B. It identifies the location of source addresses for outgoing packets to be translated using access or route maps.
C. It must be configured if static NAT is used
D. It identifies the public IP address that traffic will use to reach the internet.
Answer: B
Explanation:
This module describes how to configure Network Address Translation (NAT) for IP address conservation and how to configure inside and outside source addresses. This module also provides information about the benefits of configuring NAT for IP address conservation. NAT enables private IP internetworks that use nonregistered IP addresses to connect to the Internet. NAT operates on a device, usually connecting two networks, and translates the private (not globally unique) addresses in the internal network into legal addresses before packets are forwarded onto another network. NAT can be configured to advertise to the outside world only one address for the entire network. This ability provides additional security by effectively hiding the entire internal network behind that one address. NAT is also used at the enterprise edge to allow internal users access to the Internet and to allow Internet access to internal devices such as mail servers.
Q4. - (Topic 3)
Identify the four valid IPv6 addresses. (Choose four.)
A. ::
B. ::192:168:0:1
C. 2000::
D. 2001:3452:4952:2837::
E. 2002:c0a8:101::42
F. 2003:dead:beef:4dad:23:46:bb:101
Answer: A,B,E,F
Explanation:
http://www.intermapper.com/ipv6validator http://www.ripe.net/lir-services/new-lir/ipv6_reference_card.pdf
Q5. - (Topic 1)
Refer to the topology and switching table shown in the graphic.
Host B sends a frame to Host C. What will the switch do with the frame?
A. Drop the frame
B. Send the frame out all ports except port 0/2
C. Return the frame to Host B
D. Send an ARP request for Host C
E. Send an ICMP Host Unreachable message to Host B
F. Record the destination MAC address in the switching table and send the frame directly to Host C
Answer: B
Q6. - (Topic 7)
Which component of the routing table ranks routing protocols according to their preferences?
A. administrative distance
B. next hop
C. metric
D. routing protocol code
Answer: A
Explanation:
Administrative distance - This is the measure of trustworthiness of the source of the
route. If a router learns about a destination from more than one routing protocol,
administrative distance is compared and the preference is given to the routes with lower
administrative distance. In other words, it is the believability of the source of the route.
Q7. - (Topic 3)
Refer to the output of the corporate router routing table shown in the graphic.
The corporate router receives an IP packet with a source IP address of 192.168.214.20 and a destination address of 192.168.22.3.
What will the router do with this packet?
A. It will encapsulate the packet as Frame Relay and forward it out interface Serial 0/0.117.
B. It will discard the packet and send an ICMP Destination Unreachable message out interface FastEthernet 0/0.
C. It will forward the packet out interface Serial 0/1 and send an ICMP Echo Reply message out interface serial 0/0.102.
D. It will change the IP packet to an ARP frame and forward it out FastEthernet 0/0.
Answer: B
Explanation:
Since the destination network is not in the routing table, and no default gateway has been configured, the router will discard the packet and send an ICMP Destination Unreachable message out interface FastEthernet 0/0. It knows to send it out Fa 0/0 because the routing table for the source IP address of 192.168.214.20 shows it was learned from the Fa 0/0 interface.
Q8. - (Topic 2)
How many simultaneous Telnet sessions does a Cisco router support by default?
A. 1
B. 2
C. 3
D. 4
E. 5
F. 6
Answer: E
Explanation:
By default, Cisco routers support virtual terminal interfaces 0-4 (5 total) which are used for telnet sessions.
Q9. - (Topic 2)
Which address type does a switch use to make selective forwarding decisions?
A. Source IP address
B. Destination IP address
C. Source and destination IP address
D. Source MAC address
E. Destination MAC address
Answer: E
Explanation:
Switches analyze the destination MAC to make its forwarding decision since it is a layer 2 device. Routers use the destination IP address to make forwarding decisions.
Q10. - (Topic 3)
Why do large OSPF networks use a hierarchical design? (Choose three.)
A. to decrease latency by increasing bandwidth
B. to reduce routing overhead
C. to speed up convergence
D. to confine network instability to single areas of the network
E. to reduce the complexity of router configuration
F. to lower costs by replacing routers with distribution layer switches
Answer: B,C,D
Explanation:
OSPF implements a two-tier hierarchical routing model that uses a core or backbone tier known as area zero (0). Attached to that backbone via area border routers (ABRs) are a number of secondary tier areas.
The hierarchical approach is used to achieve the following:
. Rapid convergence because of link and/or switch failures
. Deterministic traffic recovery
. Scalable and manageable routing hierarchy, reduced routing overhead.
Q11. - (Topic 3)
Which three statements are correct about RIP version 2? (Choose three)
A. It uses broadcast for its routing updates.
B. It supports authentication.
C. It is a classless routing protocol.
D. It has a lower default administrative distance then RIP version 1.
E. It has the same maximum hop count as RIP version 1.
F. It does not send the subnet mask any updates.
Answer: B,C,E
Explanation:
A and E are correct according to the theory of RIP.
RIP version 1 updates are broadcasts, and RIP version 2 updates are multicast to
224.0.0.9 -> B is not correct.
RIP v1 is a classful routing protocol but RIP v2 is a classless routing protocol -> C is
correct.
RIPv1 and RIPv2 have the same default administrative distance of 120 -> D is not correct.
RIPv2 is a classless routing protocol so it does send the subnet mask in updates -> F is not
correct.
Q12. - (Topic 3)
What is the network address for the host with IP address 192.168.23.61/28?
A. 192.168.23.0
B. 192.168.23.32
C. 192.168.23.48
D. 192.168.23.56
E. 192.168.23.60
Answer: C
Explanation:
Convert bit-length prefix to quad-dotted decimal representation, then from it find the number of bits used for subnetting you can find previously calculated number of subnets by separating subnets each having value of last bit used for subnet masking Find that your IP address is in which subnet, that subnet's first address is network address and last address is broadcast address. Based on above steps the answer is option C
Q13. - (Topic 3)
Refer to the exhibit.
When running OSPF, what would cause router A not to form an adjacency with router B?
A. The loopback addresses are on different subnets.
B. The values of the dead timers on the routers are different.
C. Route summarization is enabled on both routers.
D. The process identifier on router A is different than the process identifier on router B.
Answer: B
Explanation:
To form an adjacency (become neighbor), router A & B must have the same Hello interval, Dead interval and AREA numbers
Q14. - (Topic 1)
On a Cisco switch, which protocol determines if an attached VoIP phone is from Cisco or from another vendor?
A. RTP
B. TCP
C. CDP
D. UDP
Answer: C
Explanation:
The Cisco Unified IP Phone uses CDP to communicate information such as auxiliary VLAN ID, per port power management details, and Quality of Service (QoS) configuration information with the Cisco Catalyst switch. Cisco Discovery Protocol (CDP) is a proprietary protocol designed by Cisco to help administrators collect information about both locally attached and remote devices. By using CDP, you can gather hardware and protocol information about neighbor devices, which is useful info for troubleshooting the network. CDP messages are generated every 60 seconds as multicast messages on each of its active interfaces. The information shared in a CDP packet about a Cisco device includes the following: Name of the device configured with the hostname command IOS software version Hardware capabilities, such as routing, switching, and/or bridging Hardware platform, such as 2600, 2950, or 1900 The layer-3 address(es) of the device The interface the CDP update was generated on
Reference: http://computernetworkingnotes.com/cisco-devices-administration-and-configuration/cisco-discoveryprotocol.html
Q15. - (Topic 3)
What is the purpose of assigning an IP address to a switch?
A. provides local hosts with a default gateway address
B. allows remote management of the switch
C. allows the switch to respond to ARP requests between two hosts
D. ensures that hosts on the same LAN can communicate with each other
Answer: B
Explanation:
A switch is a layer 2 device and doesn’t use network layer for packet forwarding. The IP
address may be used only for administrative purposes such as Telnet access or for network management purposes.