101-01 Premium Bundle

101-01 Premium Bundle

Riverbed Certified Solutions Associate Certification Exam

4.5 
(31275 ratings)
0 QuestionsPractice Tests
0 PDFPrint version
November 21, 2024Last update

Riverbed 101-01 Free Practice Questions

Q1. When Adaptive Compression is used on a Steelhead appliance, what determines the switch to dynamically disable Lempel-Ziv compression if compression is deemed ineffective?

A. Periodic samples of data flows

B. Packet by packet analysis

C. Continual TCP session analysis

D. Reduction throttle signal from the Central Management Console (CMC)

E. Average available bandwidth

Answer: A

Q2. A customer is marking QoS between the Steelhead appliances based on the application (port number) being used. What is the recommended WAN visibility mode?

A. Correct Addressing

B. Port Transparency

C. IPSec tunnel mode

D. SSL mode

Answer: B

Q3. Steelhead appliances models vary by supported bandwidth. This bandwidth refers to:

A. All inbound and outbound traffic

B. All outbound traffic

C. All optimized inbound and optimized outbound traffic

D. All optimized outbound traffic

E. VoIP traffic only

Answer: D

Q4. What is the default action of a Steelhead appliance when it hits the bandwidth limit?

A. Fail-to-wire

B. Inbound Optimized traffic is shaped to the specifications of the Steelhead appliance

C. Passthrough all connections

D. Passthrough new connections

E. Outbound Optimized traffic is shaped to the specifications of the Steelhead appliance

Answer: E

Q5. Which of the following interfaces can be configured using the configuration wizard?

A. Primary only

B. Primary and inpath0_0

C. Inpath0_0 only

D. Primary and auxiliary

Answer: B

Q6. How many separate TCP sessions exist for each optimized connection?

A. 1

B. 2

C. 3

D. 4

E. It depends on the WAN visibility mode

Answer: C

Q7. Which of the following management or monitoring methods are supported by the Steelhead appliance? (Select 4)

A. SNMP / SNMP traps

B. Email notification

C. HP Open View Console plug-in available on Riverbed support site

D. Central Management Console

E. Syslog

Answer: ABDE

Q8. What is the command to clear all statistics on a Steelhead appliance?

A. (config) # stats clear-all

B. (config) # clear-all stats

C. (config) # reset stats

D. (config) # reload stats clean

E. (config) # clear stats

Answer: A

Q9. Which of the following deployment methods can NOT be used simultaneously on a single Steelhead appliance?

A. Logical In-path / Physical In-path

B. Server-side out-of-path / Physical In-path

C. Server-side out-of-path / Logical In-path

D. All methods above can be configured on a single Steelhead appliance simultaneously

Answer: A

Q10. Can you manage your Virtual Steelhead appliance from a Central Management Console?

A. Yes, this is possible

B. Only on out-of-path deployments

C. Only on in-path deployments

D. There is a dedicated management device for Virtual Steelhead appliances

E. You can only manage your Virtual Steelhead appliances using a virtualized console

Answer: A

Q11. When performing datastore synchronization between two Steelhead appliances, segments of data are exchanged between them. Which interfaces can be used for datastore synchronization? (Select 2)

A. In-path

B. Primary

C. Auxiliary

D. WAN

E. Remote

Answer: BC

Q12. What is the total number of optimized concurrent TCP connections supported on an Interceptor appliance?

A. 100,000

B. 200,000

C. 300,000

D. 500,000

E. 1,000,000

Answer: E

Q13. What combinations of WAN visibility modes can simultaneously be configured on Steelhead appliances?

A. It can never be done

B. Only Port Transparent

C. Only Correct Addressing

D. Only Full Addressing

E. Full Transparency, PortTransparencyand Correct Addressing can be configured simultaneously

Answer: E

Q14. What are two methods that can be configured to provide location awareness for a Steelhead Mobile client? (Select 2)

A. Adapter based configuration

B. Fixed-target rule

C. In-path rule

D. Latency detection

Answer: AD

Q15. When MAPI prepopulation is enabled, what is default TCP keep-alive time used to prepopulate the Steelhead appliance with emails and attachments?

A. 24 hours

B. 48 hours

C. 72 hours

D. 96 hours

Answer: D

Q16. How can Steelhead Mobile client software be distributed directly from the Steelhead Mobile Controller (SMC)? (Select 2)

A. HTTPS

B. HTTP

C. FTP

D. TFTP

E. NFS

Answer: AB

START 101-01 EXAM