Introducing The New!
Surepassexam Collection
Get Unlimited Access to all
Surepassexam's PREMIUM files
Q1. How many TCP connections can an Interceptor appliance set up per second?
A. 1000
B. 2000
C. 3000
D. 4000
E. 5000 or over
Answer: E
Q2. Which of the following factors are important to consider when sizing a Steelhead appliance? (Select 3)
A. Number of simultaneous optimized connections
B. The maximum optimized WAN bandwidth
C. The size of datastore
D. The number of applications used by the enterprise
Answer: ABC
Q3. All of the following are types of peering rules, except:
A. Pass
B. Accept
C. Discard
D. Auto
Answer: C
Q4. What are the three WAN visibility modes supported in the Steelhead appliances?
A. Normal mode, Tunnel mode, Secure mode
B. Normal mode, Correct Addressing, Tunnel mode
C. Secure mode, Tunnel mode, Full Transparency mode
D. Correct Addressing, Port Transparency, Full Transparency
Answer: D
Q5. Refer to the exhibit.
Which of the following correctly describes the combination of cable types used in a fail-to-wire scenario for the interconnected devices shown in the exhibit? Assume Auto-MDIX is not enabled on any device.
A. Cable 1: Crossover, Cable 2: Crossover
BCable 1: Straight-through, Cable 2: Straight-through
B. Cable 1: Crossover, Cable 2: Straight-through
C. Cable 1: Straight-through, Cable 2: Crossover
Answer: C
Q6. An employee who has just installed Steelhead Mobile onto her workstation notices that she never gets any reduction. It always says 0%.
The status of the Mobile client appears to be:
Optimization State: Healthy
Controller Status: Connected: Branch
The reason she is seeing 0% reduction statistics is:
A. Location Awareness is in effect
B. The Steelhead appliance in the branch office has currently failed
C. There are no more Steelhead Mobile licenses available
D. The Steelhead Mobile Controller is not available as it has been relocated to a branch office
E. Steelhead Mobile does not work on workstations, only laptops
Answer: A
Q7. Assume the SSL server is configured for the default SSL port. Which port has to be specified in the in-path rules of the client-side Steelhead appliance?
A. 443
B. 445
C. 7801
D. 8080
Answer: A
Q8. After deployment of Steelhead appliances, a certain backup application shows poor bandwidth reduction. After disabling the backup application's native compression algorithm, the bandwidth reduction statistics on the Steelhead appliances suddenly improve significantly. Which of the following are likely causes for the increased bandwidth reduction?
A. The native compression algorithm of the backup application could not be compressed further
B. The application-level protocol used by the backup application is not recognized by the Steelhead appliances
C. The Steelhead appliances were not able to effectively perform TCP optimizations
D. There should be no difference between compressed and uncompressed traffic
Answer: A
Q9. Rules that dictate the types of TCP traffic that a Steelhead Mobile client should optimize are configured in the:
A. Acceleration policy
B. Authorization policy
C. Peering rules
D. Fixed target policy
Answer: A
Q10. A Steelhead appliance can continue to optimize traffic in which of the following status states? (Select 2)
A. Healthy
B. Normal
C. Critical
D. Degraded
E. Failed
Answer: AD
Q11. In an in-path deployment, when a Steelhead appliance fails to wire, the Steelhead appliance acts as a:
A. Straight-through cable
B. Crossover cable
C. Router
D. Firewall
E. None of the above
Answer: B
Q12. Which xx50 Steelhead appliance models provide both inpath0_0 and inpath0_1 interfaces without adding additional network cards? (Select 3)
A. Steelhead 550
B. Steelhead 6050
C. Steelhead 1050
D. Steelhead 250
E. Steelhead 2050
Answer: BCE
Q13. When implementing PBR, a Steelhead appliance is connected to the router using which Steelhead appliance interface?
A. lan0_0
B. wan0_0
C. Primary
D. AUX
E. Remote
Answer: B
Q14. The default action performed by the Steelhead appliance when it receives a packet with an existing DSCP value 46 is to:
A. Override the value with a default of 0
B. Override the value with the value of AF11
C. Reflect the value received by the original packet
D. Reflect the value returned by the symmetric TCP flow
Answer: C
Q15. A Steelhead appliance can be configured to automatically send an email to a preconfigured email address in the event of a failure. Where is this done? (Select 3)
A. GUI
B. CLI
C. RADIUS/TACACS+
D. Can be done via the Central Management Console
E. DNS server
Answer: ABD
Q16. What is the default QoS classification mode?
A. Flat
B. Hierarchical
C. WRED
D. LLQ
E. FEC
Answer: A