Introducing The New!
Surepassexam Collection
Get Unlimited Access to all
Surepassexam's PREMIUM files
P.S. Approved 200-125 testing software are available on Google Drive, GET MORE: https://www.slideshare.net/reinigerodp/certleader-200-125examquestionsmaterials
New Questions 14
Which Cisco platform can verify ACLs?
A. Cisco Prime Infrastructure
B. Cisco Wireless LAN Controller
C. Cisco APIC-EM
D. Cisco IOS-XE
Answer: B
New Questions 15
Which function of the IP SLAs ICMP jitter operation can you use to determine whether a VoIP issue is caused by excessive end-to-end time?
A. packet loss
B. jitter
C. successive packet loss
D. round-trip time latency
Answer: D
New Questions 16
Which NAT type is used to translate a single inside address to a single outside address?
A. dynamic NAT
B. NAT overload
C. PAT
D. static NAT
Answer: D
Explanation:
Network address translation (NAT) is the process ofmodifying IP addressinformation in IP packet headers while in transit across a traffic routing device.
There are two different types of NAT:
u2711 NAT
u2711 PAT
New Questions 17
Which command can you enter to configure a local username with an encrypted password and EXEC mode user privileges?
A. Router(config)#username jdone privilege 1 password 7 08314D5D1A48
B. Router(config)#username jdone privilege 1 password 7 PASSWORD1
C. Router(config)#username jdone privilege 15 password 0 08314D5D1A48
D. Router(config)#username jdone privilege 15 password 0 PASSWORD1
Answer: A
New Questions 18
Which effect of the passive-Interface command on R1 is true?
A. It removes the 172.16.0.0 network from all updates on all interfaces on R1.
B. It prevents interface Fa0/0 from sending updates.
C. Interface Fa0/0 operates in RIPv1 mode.
D. It removes the 172.17.0.0 network from all updates on all interfaces on R1.
Answer: B
New Questions 19
Which two statements about late collisions are true? (Choose two.)
A. They may indicate a duplex mismatch.
B. By definition, they occur after the 512th bit of the frame has been transmitted.
C. They indicate received frames that did not pass the FCS match.
D. They are frames that exceed 1518 bytes.
E. They occur when CRC errors and interference occur on the cable.
Answer: A,B
New Questions 20
If router R1 knows a static route to a destination network and then learn about the same destination network through a dynamic routing protocol, how does R1 respond?
A. It sends a withdrawal notification to the neighboring router.
B. It refuses to advertise the dynamic route to other neighbors.
C. It disables the routing protocol.
D. It prefers the static route.
Answer: D
New Questions 21
Which statement about unicast frame forwarding on a switch is true?
A. The TCAM table stores destination MAC addresses
B. If the destination MAC address is unknown, the frame is flooded to every port that is configured in the same VLAN except on the port that it was received on.
C. The CAM table is used to determine whether traffic is permitted or denied on a switch
D. The source address is used to determine the switch port to which a frame is forwarded
Answer: B
New Questions 22
By default, how many MAC addresses are permitted to be learned on a switch port with port security enabled?
A. 8
B. 2
C. 1
D. 0
Answer: C
New Questions 23
Why is the Branch2 network 10.1 0.20.0/24 unable to communicate with the Server farm1 network 10.1 0.10.0/24 over the GRE tunnel?
A. The GRE tunnel destination is not configured on the R2 router.
B. The GRE tunnel destination is not configured on the Branch2 router.
C. The static route points to the tunnel0 interface that is misconfigured on the Branch2 router.
D. The static route points to the tunnel0 interface that is misconfigured on the R2 router.
Answer: C
Explanation:
The Branch2 network is communicating to the Server farm, which is connected to R2, via GRE Tunnel so we should check the GRE tunnel first to see if it is in u201cup/upu201d state with the u201cshow ip interface briefu201d command on the two routers.
On Branch2:
On R2:
We see interfaces Tunnel0 at two ends are u201cup/upu201d which are good so we should check for the routing part on two routers with the u201cshow running-configu201d command and pay attention to the static routing of each router. On Branch2 we see:
R2_show_run_static.jpg
The destination IP address for this static route is not correct. It should be 192.168.24.1 (Tunnel0u2021s IP address of R2), not 192.168.24.10 -> Answer C is correct.
Note: You can use the u201cshow ip routeu201d command to check the routing configuration on each router but if the destination is not reachable (for example: we configure u201cip route 10.10.10.0 255.255.255.0 192.168.24.10u201d on Branch2, but if 192.168.24.10 is unknown then Branch2 router will not display this routing entry in its routing table.
P.S. Easily pass 200-125 Exam with Allfreedumps Approved Dumps & pdf vce, Try Free: https://www.allfreedumps.com/200-125-dumps.html (890 New Questions)