Introducing The New!
Surepassexam Collection
Get Unlimited Access to all
Surepassexam's PREMIUM files
Q1. - (Topic 8)
Which network topology allows all traffic to flow through a central hub?
A. bus
B. star
C. mesh
D. ring
Answer: B
Q2. - (Topic 8)
Which command can you enter to set the default route for all traffic to an interface?
A. router(config)#ip route 0.0.0.0 0.0.0.0 GigabitEthernet0/1
B. router(config)#ip route 0.0.0.0 255.255.255.255 GigabitEthernet0/1
C. router(config-router)#default-information originate
D. router(config-router)#default-information originate always
Answer: A
Q3. - (Topic 5)
Which statement describes the process of dynamically assigning IP addresses by the DHCP server?
A. Addresses are allocated after a negotiation between the server and the host to determine the length of the agreement.
B. Addresses are permanently assigned so that the hosts uses the same address at all times.
C. Addresses are assigned for a fixed period of time, at the end of the period, a new request for an address must be made.
D. Addresses are leased to hosts, which periodically contact the DHCP server to renew the lease.
Answer: D
Explanation:
The DHCP lifecycle consists of the following:
✑ Allocation: A client begins with no active lease, and hence, no DHCP-assigned address. It acquires a lease through a process of allocation.
✑ Reallocation: If a client already has an address from an existing lease, then when it reboots or starts up after being shut down, it will contact the DHCP server that granted it the lease to confirm the lease and acquire operating parameters. This is sometimes called reallocation; it is similar to the full allocation process but shorter.
✑ Normal Operation: Once a lease is active, the client functions normally, using its assigned IP address and other parameters during the “main part” of the lease. The client is said to be bound to the lease and the address.
✑ Renewal: After a certain portion of the lease time has expired, the client will attempt to contact the server that initially granted the lease, to renew the lease so it can keep using its IP address.
✑ Rebinding. If renewal with the original leasing server fails (because, for example, the server has been taken offline), then the client will try to rebind to any active DHCP server, trying to extend its current lease with any server that will allow it to do so.
✑ Release: The client may decide at any time that it no longer wishes to use the IP address it was assigned, and may terminate the lease, releasing the IP address.
Q4. - (Topic 4)
Refer to the exhibit.
In the Frame Relay network, which IP addresses would be assigned to the interfaces with point-to-point PVCs?
A. DLCI 16: 192.168.10.1 /24
DLCI 17: 192.168.10.1 /24
DLCI 99: 192.168.10.2 /24
DLCI 28: 192.168.10.3 /24
B. DLCI 16: 192.168.10.1 /24
DLCI 17: 192.168.11.1 /24
DLCI 99: 192.168.12.1 /24
DLCI 28: 192.168.13.1 /24
C. DLCI 16: 192.168.10.1 /24
DLCI 17: 192.168.11.1 /24
DLCI 99: 192.168.10.2 /24
DLCI 28: 192.168.11.2 /24
D. DLCI 16: 192.168.10.1 /24
DLCI 17: 192.168.10.2 /24
DLCI 99: 192.168.10.3 /24
DLCI 28: 192.168.10.4 /24
Answer: C
Explanation:
With point to point PVC’s, each connection needs to be in a separate subnet. The R2-R1 connection (DLCI 16 to 99) would have each router within the same subnet. Similarly, the R3-R1 connection would also be in the same subnet, but it must be in a different one than the R2-R1 connection.
Q5. - (Topic 5)
Which command can you use to manually assign a static IPv6 address to a router interface?
A. ipv6 autoconfig 2001:db8:2222:7272::72/64
B. ipv6 address 2001:db8:2222:7272::72/64
C. ipv6 address PREFIX_1 ::1/64
D. ipv6 autoconfig
Answer: B
Explanation:
To assign an IPv6 address to an interface, use the “ipv6 address” command and specify the IP address you wish to use.
Q6. - (Topic 5)
Refer to the diagram.
All hosts have connectivity with one another. Which statements describe the addressing scheme that is in use in the network? (Choose three.)
A. The subnet mask in use is 255.255.255.192.
B. The subnet mask in use is 255.255.255.128.
C. The IP address 172.16.1.25 can be assigned to hosts in VLAN1
D. The IP address 172.16.1.205 can be assigned to hosts in VLAN1
E. The LAN interface of the router is configured with one IP address.
F. The LAN interface of the router is configured with multiple IP addresses.
Answer: B,C,F
Explanation:
The subnet mask in use is 255.255.255.128: This is subnet mask will support up to 126 hosts, which is needed.
The IP address 172.16.1.25 can be assigned to hosts in VLAN1: The usable host range in this subnet is 172.16.1.1-172.16.1.126
The LAN interface of the router is configured with multiple IP addresses: The router will need 2 subinterfaces for the single physical interface, one with an IP address that belongs in each VLAN.
Q7. - (Topic 4)
Which protocol is an open standard protocol framework that is commonly used in VPNs, to provide secure end-to-end communications?
A. RSA
B. L2TP
C. IPsec
D. PPTP
Answer: C
Explanation:
IPSec is a framework of open standards that provides data confidentiality, data integrity, and data authentication between participating peers at the IP layer. IPSec can be used to protect one or more data flows between IPSec peers.
Q8. DRAG DROP - (Topic 4)
Drag the Frame Relay acronym on the left to match its definition on the right. (Not all acronyms are used.)
Answer:
Q9. - (Topic 8)
Why is the Branch2 network 10.1 0.20.0/24 unable to communicate with the Server farm1 network 10.1 0.10.0/24 over the GRE tunnel?
A. The GRE tunnel destination is not configured on the R2 router.
B. The GRE tunnel destination is not configured on the Branch2 router.
C. The static route points to the tunnel0 interface that is misconfigured on the Branch2 router.
D. The static route points to the tunnel0 interface that is misconfigured on the R2 router.
Answer: C
Q10. - (Topic 6)
A network administrator needs to configure port security on a switch. Which two statements are true? (Choose two.)
A. The network administrator can apply port security to dynamic access ports.
B. The network administrator can apply port security to EtherChannels.
C. When dynamic MAC address learning is enabled on an interface, the switch can learn new addresses, up to the maximum defined.
D. The sticky learning feature allows the addition of dynamically learned addresses to the running configuration.
E. The network administrator can configure static secure or sticky secure MAC addresses in the voice VLAN.
Answer: C,D
Explanation:
Follow these guidelines when configuring port security:
+ Port security can only be configured on static access ports, trunk ports, or 802.1Q tunnel ports.
+ A secure port cannot be a dynamic access port.
+ A secure port cannot be a destination port for Switched Port Analyzer (SPAN).
+ A secure port cannot belong to a Fast EtherChannel or Gigabit EtherChannel port group.
+ You cannot configure static secure or sticky secure MAC addresses on a voice VLAN.
+ When you enable port security on an interface that is also configured with a voice VLAN, you must set the maximum allowed secure addresses on the port to at least two.
+ If any type of port security is enabled on the access VLAN, dynamic port security is automatically enabled on the voice VLAN.
+ When a voice VLAN is configured on a secure port that is also configured as a sticky secure port, all addresses seen on the voice VLAN are learned as dynamic secure addresses, and all addresses seen on the access VLAN (to which the port belongs) are learned as sticky secure addresses.
+ The switch does not support port security aging of sticky secure MAC addresses.
+ The protect and restrict options cannot be simultaneously enabled on an interface.
(Reference: http://www.cisco.com/en/US/docs/switches/lan/catalyst3550/software/release/12.1_19_ea1
/configuration/guide/swtrafc.html)
Q11. - (Topic 6)
When you are troubleshooting an ACL issue on a router, which command would you use to verify which interfaces are affected by the ACL?
A. show ip access-lists
B. show access-lists
C. show interface
D. show ip interface
E. list ip interface
Answer: D
Explanation:
Incorrect Answer
show ip access-lists does not show interfaces affected by an ACL.
Q12. - (Topic 4)
Refer to the exhibit.
What is the meaning of the term dynamic as displayed in the output of the show frame- relay map command shown?
A. The Serial0/0 interface is passing traffic.
B. The DLCI 100 was dynamically allocated by the router.
C. The Serial0/0 interface acquired the IP address of 172.16.3.1 from a DHCP server.
D. The DLCI 100 will be dynamically changed as required to adapt to changes in the Frame Relay cloud.
E. The mapping between DLCI 100 and the end station IP address 172.16.3.1 was learned through Inverse ARP.
Answer: E
Explanation:
Inverse Address Resolution Protocol (Inverse ARP) was developed to provide a mechanism for dynamic DLCI to Layer 3 address maps. Inverse ARP works much the same way Address Resolution Protocol (ARP) works on a LAN. However, with ARP, the device knows the Layer 3 IP address and needs to know the remote data link MAC address. With Inverse ARP, the router knows the Layer 2 address which is the DLCI, but needs to know the remote Layer 3 IP address.
When using dynamic address mapping, Inverse ARP requests a next-hop protocol address for each active PVC. Once the requesting router receives an Inverse ARP response, it updates its DLCI-to-Layer 3 address mapping table. Dynamic address mapping is enabled by default for all protocols enabled on a physical interface. If the Frame Relay environment supports LMI autosensing and Inverse ARP, dynamic address mapping takes place automatically. Therefore, no static address mapping is required.
Q13. - (Topic 5)
Which subnet mask would be appropriate for a network address range to be subnetted for up to eight LANs, with each LAN containing 5 to 26 hosts?
A. 0.0.0.240
B. 255.255.255.252
C. 255.255.255.0
D. 255.255.255.224
E. 255.255.255.240
Answer: D
Explanation:
For a class C network, a mask of 255.255.255.224 will allow for up to 8 networks with 32 IP addresses each (30 usable).
Q14. - (Topic 8)
What is one requirement for interfaces to run IPv6?
A. An IPv6 address must be configured on the interface.
B. An IPv4 address must be configured.
C. Stateless autoconfiguration must be enabled after enabling IPv6 on the interface.
D. IPv6 must be enabled with the ipv6 enable command in global configuration mode.
Answer: A
Explanation: To use IPv6 on your router, you must, at a minimum, enable the protocol and assign IPv6 addresses to your interfaces.
Q15. - (Topic 3)
Refer to the exhibit.
What can be determined about the router from the console output?
A. No configuration file was found in NVRAM.
B. No configuration file was found in flash.
C. No configuration file was found in the PCMCIA card.
D. Configuration file is normal and will load in 15 seconds.
Answer: A
Explanation:
When no startup configuration file is found in NVRAM, the System Configuration Dialog will appear to ask if we want to enter the initial configuration dialog or not.