Introducing The New!
Surepassexam Collection
Get Unlimited Access to all
Surepassexam's PREMIUM files
Q1. RAG DROP
Answer:
Q2. What two capabilities would be present on a wireless client device that supports CCXv3? (Choose two.)
A. WPA2
B. 802.1x
C. PEAP-MSCHAP
D. NAC
E. MFP
F. EAP-TLS
Answer: A,B
Q3. A customer has asked for its wireless equipment to be managed as securely as possible. Which three management protocols will provide encrypted access to the equipment? (Choose three.)
A. Secure Shell
B. HTTPS
C. SNMPv3
D. Telnet
E. SNMPv2c
F. HTTP
Answer: A,B,C
Q4. What are the interface statuses of a lightweight AP working in rogue-detection mode?
A. radios turned off, Ethernet interface up
B. radios and Ethernet interfaces up
C. radios turned on, Ethernet interface shut down
D. radios turned on, Ethernet interface status controlled by Cisco WLC
Answer: A
Q5. What technology consists of small, low-power digital radios?
A. LTE
B. WiFi
C. ZigBee
D. Bluetooth
Answer: C
Q6. On the Cisco Wireless LAN Controller GUI, what sub-menu option under the Command menu will transfer code and configuration files to the controller?
A. Download File
B. Upload File
C. Download Configuration
D. Upload Configuration
Answer: A
Q7. When adding a controller to manage through Cisco WCS, which address type is used and which SNMP function does the Cisco WCS perform?
A. The controller is managed through its MAC address and the Cisco WCS acts as a SNMP TRAP authenticator.
B. The IP address of the controller is used and the Cisco WCS acts as a SNMP TRAP receiver.
C. The controller is managed through its MAC address and the Cisco WCS acts as a SNMP agent.
D. The controller connects through its MAC address to the Cisco WCS and the Cisco WCS uses the SNMP to manage the controller for all configured SNMP parameters.
Answer: B
Q8. Which interface is considered a dynamic interface?
A. the virtual interface
B. the AP manager interface
C. the LAG interface
D. the management interface
E. the service port interface
F. a WLAN client data interface
Answer: F
Q9. What protocol overcomes the weaknesses of LEAP?
A. EAP-TLS
B. PEAP
C. EAP-FAST
D. EAP-TTLS
Answer: C
Q10. Refer to the exhibit. An engineer wants to setup a mobility anchor for the Guest WLAN, but does not see the Anchor IP address listed in the drop-down. What is the most likely cause of this problem?
A. The mobility anchor is currently unreachable.
B. The mobility anchor must also be included in the mobility group of the WLC.
C. Layer 3 Security must be configured for Web Policy Authentication.
D. The mobility anchor is attached to another WLAN.
E. Layer 3 Security must be configured for Web Policy Passthrough.
Answer: B
Q11. A customer wants to deploy a mesh network with 2 root access points and 10 mesh access points. The root access points should be configured as which mode on the WLC?
A. mesh
B. FlexConnect
C. bridge
D. rouge detection
E. sniffer
Answer: C
Q12. Which Cisco WLC command family can help to troubleshoot communication between an AP and the WLC?
A. (Cisco Controller) >debug capwap
B. (Cisco Controller) >debug ap
C. (Cisco Controller) >debug cac
D. (Cisco Controller) >debug dot11
Answer: A
Q13. Which option describes why most wireless phones and tablets do not use 802.11a/n and 40 MHz channels?
A. a lack of radio range when using these radios
B. a lack of device battery capacity to operate concurrent a/b/g/n radios
C. a lack of cooling in the device necessary to operate these radios
D. These radios would require the devices to be larger.
Answer: B
Q14. RAG DROP
Answer:
Q15. An engineer assists a user in configuring an Android device for authentication to an IEEE 802.1x EAP WLAN with PEAPv1. The Phase 2 authentication should be configured as which option?
A. LEAP
B. MSCHAPv2
C. TLS
D. TTLS
Answer: B