Cisco 200-355 Free Practice Questions

New Questions 1

When a guest client is authenticated, which type of connection is created between the controller-based AP and the client?

A. as SSL connection

B. a TLS encrypted tunnel

C. an unsecured connection

D. a 802.1x/EAP tunnel

E. an IPsec tunnel

View Answer

New Questions 2

What protocol is used to determine the best pathway back to a root access point?

A. CCKM

B. WNMP

C. AWPP

D. LWAP

View Answer

New Questions 3

An 802.11g network is experiencing intermittent signal degradation and Spectrum Analyzer is being used to try and locate the problem. What two interferers would likely be identified? (Choose two.)

A. multiple cell phones

B. microwave oven

C. FM Radio

D. cordless phone

E. document scanner

View Answer

New Questions 4

A controller is connected to a Cisco Catalyst switch. The switch port configuration looks like this:

interface GigabitEthernet 1/0/10 switchport

switchport trunk encapsulation dot1q switchport trunk allowed vlan 1,20,30,50 switchport trunk native vlan 20 switchport mode trunk

Which controller CLI command assigns its management interface to the native VLAN interface of the Cisco Catalyst switch?

A. config interface vlan management 0

B. config interface vlan management 1

C. config interface vlan management 20

D. config interface vlan management 30

E. config interface vlan management 50

View Answer

New Questions 5

Which two Cisco Unified Wireless Network capabilities use information that is provided by Radio Resource Management neighbor messages in version 7.0 MR1? (Choose two.)

A. aggressive load balancing

B. dynamic channel assignment

C. hybrid remote edge access point

D. inter-controller mobility (that is, mobility groups)

E. rogue AP classification

View Answer

New Questions 6

A customer has asked for the proper port configuration to allow for LAG on a Cisco 2504 Wireless Controller to a Cisco IOS switch. Which EtherChannel mode should be used on the switch to allow for the WLC to connect?

A. on

B. auto

C. desirable

D. passive

E. active

View Answer

New Questions 7

During a wireless site survey, the signal strength drops significantly when outside of the room containing the access point. The building is made of wood and drywall. This is an example of which wireless anomaly?

A. absorption

B. refraction

C. fading

D. multipath

E. reflection

View Answer

New Questions 8

When Cisco AnyConnect modules are installed on a PC, which module must be installed first?

A. telemetry

B. web security

C. VPN

D. NAM

E. DART

F. posture

G. CSSC

View Answer

New Questions 9

Which two principles must be considered when deploying a wireless network through a wooded area? (Choose two.)

A. absorption

B. reflection

C. diffraction

D. scattering

E. refraction

View Answer

New Questions 10

What is the difference between the IEEE, the WiFi Alliance, and the FCC, ETSI, and TELEC?

A. The IEEE and FCC are responsible for the standards that apply to wireless networks. The WiFi Alliance, ETSI, and TELEC are the governmental agencies that regulate compliance with local standards.

B. The IEEE is responsible for Layer 1 and Layer 2 protocols. The WiFi Alliance is responsible for interoperability testing. The FCC, ETSI, and TELEC are responsible for radio frequency and transmission power-level regulations and standards in the U.S., Europe, and Japan.

C. The IEEE is responsible for Layer 1 and Layer 2 protocols. The FCC, ETSI, and TELEC are responsible for interoperability testing and compliance. The WiFi Alliance is responsible for radio frequency and transmission power-level regulations and standards on a global basis.

D. The IEEE and FCC are responsible for the Layer 3 protocol support and frequency and power-level regulations in the United States. ETSI and TELEC are responsible for frequency and power-level regulations in Europe and Japan. The WiFi Alliance is responsible to interoperability testing.

View Answer