Introducing The New!
Surepassexam Collection
Get Unlimited Access to all
Surepassexam's PREMIUM files
Q1. Which three items do you need to establish a wireless connection to an enterprise wireless network? (Choose three.)
A. SSID name
B. RF channel
C. RF signal
D. 802.1X/EAP credentials
E. pre-shared key
F. web page
G. WPA/WPA2 settings
Answer: A,C,D
Q2. Which three options relate to event-driven RRM? (Choose three.)
A. any 802.11n AP models
B. specific AP models
C. minimum of AP and WLC
D. minimum of AP, WLC, and WCS
E. minimum of AP, WLC, WCS, and MSE
F. configurable in WLC at 802.11b/g/n > RRM > TPC
G. configurable in WLC at 802.11b/g/n > RRM > DCA
Answer: B,C,G
Q3. Refer to the exhibit. Which two wireless functions is the client experiencing? (Choose two.)
A. Inter-controller Roaming
B. Intra-controller Roaming
C. Layer 2 Roaming
D. Layer 3 Roaming
E. Inter-subnet roaming
F. Re-authentication
Answer: B,C
Q4. An engineer recently removed a WLC from a WCS, but the APs associated to the WLC are still showing on the WCS. What is a reason for this?
A. The associated APs must be removed manually.
B. The APs must be removed from the WCS map.
C. The hold-down timer must expire before the APs will be removed.
D. The APs must be audited.
Answer: A
Q5. Refer to the exhibit. In an effort to identify RF characteristics at a customer location, an RF engineer uses the Spectrum Analyzer tool that is shown. Which feature that is native to the Spectrum Analyzer is identified by the exhibit?
A. Real-Time FFT
B. Duty Cycle
C. Max Hold
D. Time Domain
Answer: A
Q6. When using multiple SSIDs on a lightweight AP, how does the traffic of each SSID reach the 802.3 network?
A. provide routing between them at the core so that the SSIDs can reach the internet
B. configure 802.11q trunking on the Ethernet switch port that is connected to the AP
C. configure ACLs at the switch port that will allow all desired SSIDs to pass traffic
D. configure the SSIDs on the WLC and it will regulate the traffic based on traffic type
Answer: B
Q7. What is the difference between the IEEE, the WiFi Alliance, and the FCC, ETSI, and TELEC?
A. The IEEE and FCC are responsible for the standards that apply to wireless networks. The WiFi Alliance, ETSI, and TELEC are the governmental agencies that regulate compliance with local standards.
B. The IEEE is responsible for Layer 1 and Layer 2 protocols. The WiFi Alliance is responsible for interoperability testing. The FCC, ETSI, and TELEC are responsible for radio frequency and transmission power-level regulations and standards in the U.S., Europe, and Japan.
C. The IEEE is responsible for Layer 1 and Layer 2 protocols. The FCC, ETSI, and TELEC are responsible for interoperability testing and compliance. The WiFi Alliance is responsible for radio frequency and transmission power-level regulations and standards on a global basis.
D. The IEEE and FCC are responsible for the Layer 3 protocol support and frequency and power-level regulations in the United States. ETSI and TELEC are responsible for frequency and power-level regulations in Europe and Japan. The WiFi Alliance is responsible to interoperability testing.
Answer: B
Q8. When using a Cisco WLC version 7.0 with a default configuration, how is a remote management HTTPS access connection secured?
A. The Cisco WLC uses a pre-shared key to authenticate the user, which limits the number of potential users that can access the controller.
B. The Cisco WLC generates its own local web administration SSL certificate and automatically applies it to the GUI.
C. The Cisco WLC uses a CA certificate for SSL access.
D. The Cisco WLC uses HTTPS to secure the HTTP session via a preconfigured password that generates a certificate for each session.
Answer: B
Q9. Which three Cisco Unified Wireless Network capabilities use information that is provided by Radio Resource Management neighbor messages? (Choose three.)
A. aggressive load balancing
B. dynamic channel assignment
C. hybrid remote edge access point
D. inter controller mobility (that is, mobility groups)
E. over-the-air provisioning
F. rogue AP classification
Answer: B,E,F
Q10. A customer cannot access the GUI on the Cisco 5508 Wireless Controller from the management interface due to network failure. Which interface can the customer use to access the WLC GUI until the network issues are resolved?
A. virtual
B. dynamic
C. console port
D. service port
Answer: D
Q11. When using the CLI command eping, configured for auto-anchor mobility wireless guest access, which type of packet is tested?
A. data packets
B. mobility unencrypted packets
C. mobility encrypted packets
D. SNMP control packets
E. NTP control packets
Answer: A
Q12. Refer to the exhibit.
You made a manual configuration change to a controller and now you need to compare the controller configuration seen on Cisco WCS to the configuration that is present in the controller.
Which menu can you use to do compare the configurations?
A. Reports
B. Monitor
C. Configure
D. Services
E. Administration
F. Tools
Answer: C
Q13. Refer to the exhibit. Based on the diagram, what two design requirements must be met? (Choose two.)
A. WGB is Autonomous
B. WGB is Universal
C. WGB can be Autonomous or Universal
D. Upstream AP is Aironet
E. Upstream AP is not Aironet
F. Upstream AP can be any make/model
Answer: A,D
Q14. Refer to the exhibit. An engineer wants to setup a mobility anchor for the Guest WLAN, but does not see the Anchor IP address listed in the drop-down. What is the most likely cause of this problem?
A. The mobility anchor is currently unreachable.
B. The mobility anchor must also be included in the mobility group of the WLC.
C. Layer 3 Security must be configured for Web Policy Authentication.
D. The mobility anchor is attached to another WLAN.
E. Layer 3 Security must be configured for Web Policy Passthrough.
Answer: B
Q15. Which two actions are best for deploying VoWLAN on a wireless network? (Choose two.)
A. Minimize the use of Class 3 Bluetooth devices.
B. Minimize the use of analog cameras.
C. Minimize the use of IP cameras.
D. Maximize client access by enabling all data rates used by clients.
E. Maximize client access by enabling only a few high data rates used by clients.
Answer: B,E