Introducing The New!
Surepassexam Collection
Get Unlimited Access to all
Surepassexam's PREMIUM files
Q1. An engineer is trying to determine from the controller CLI whether or not Telnet is enabled on the wireless controller. Which command can be entered to display this information?
A. show network summary
B. show aaa auth
C. show radius summary
D. show ldap statistics
Answer: A
Q2. What are the interface statuses of a lightweight AP working in rogue-detection mode?
A. radios turned off, Ethernet interface up
B. radios and Ethernet interfaces up
C. radios turned on, Ethernet interface shut down
D. radios turned on, Ethernet interface status controlled by Cisco WLC
Answer: A
Q3. Access points must discover a wireless LAN controller before they can become an active part of the network. In which order does an access point try to discover a controller?
A. Layer 3 CAPWAP or LWAPP broadcast discovery DHCP option 43 Locally stored controller IP address discovery DNS controller name resolution
B. Layer 3 CAPWAP or LWAPP broadcast discovery Locally stored controller IP address discovery DNS controller name resolution DHCP option 43
C. Layer 3 CAPWAP or LWAPP broadcast discovery Locally stored controller IP address discovery DHCP option 43 DNS controller name resolution
D. DNS controller name resolution DHCP option 43 Layer 3 CAPWAP or LWAPP broadcast discovery Locally stored controller IP address discovery
Answer: C
Q4. Refer to the exhibit.
Which two menus do you click to determine the reachability status of a controller from Cisco WCS? (Choose two.)
A. Monitor
B. Reports
C. Configure
D. Services
E. Administration
F. Tools
Answer: A,C
Q5. You are about to use a hotel's guest wireless services using a wireless laptop.
Which three items do you need to establish a wireless connection? (Choose three.)
A. SSID name
B. RF channel
C. RF signal
D. 802.1X/EAP credentials
E. pre-shared key
F. web page
G. WPA/WPA2 settings
Answer: A,C,F
Q6. Which protocol is used for Cisco WCS to communicate with Cisco WLC?
A. SNMP
B. CAPWAP
C. HTTPS
D. SSH
Answer: A
Q7. Which two items are needed to discover the IP address of a new Cisco Aironet 1260 autonomous AP that just finished booting? (Choose two.)
A. username = "cisco" and password = "cisco"
B. username = "Admin" and password = "Cisco"
C. username=Cisco and password=Cisco
D. show int vlan1
E. show int bvi1
F. show int gigabitethernet0
G. show int radio0-802.11n
H. show int radio1-802.11n
Answer: C,E
Q8. When adding a controller to manage through Cisco WCS, which address type is used and which SNMP function does the Cisco WCS perform?
A. The controller is managed through its MAC address and the Cisco WCS acts as a SNMP TRAP authenticator.
B. The IP address of the controller is used and the Cisco WCS acts as a SNMP TRAP receiver.
C. The controller is managed through its MAC address and the Cisco WCS acts as a SNMP agent.
D. The controller connects through its MAC address to the Cisco WCS and the Cisco WCS uses the SNMP to manage the controller for all configured SNMP parameters.
Answer: B
Q9. When using DHCP option 43, the discovery option supports vendor specific identifiers in order to obtain what IP address?
A. core router's gateway
B. closest distribution switch
C. local WLAN controller
D. local Radius Server
Answer: C
Q10. Which key combination provides a detailed wireless connection status for an Apple MacBook running 10.6?
A. Command + Click the SSID of the network
B. Alt + Click the SSID of the network
C. Command + the Airport icon
D. Option + the Airport icon
E. Ctrl + the Airport Icon
F. Option + Click the SSID of the network
Answer: D
Q11. RAG DROP
Answer:
Q12. An engineer is trying to identify if radar has impacted the wireless network at a customer site. When using the controller GUI, which dashboard in the Monitor section presents this information?
A. 802.11a/n - Air Quality Reports
B. Clean Air - Worst Air Quality Report
C. 802.11b/g/n - Interfering Devices
D. Statistics - Mobility Statistics
Answer: A
Q13. An engineer is using a predictive survey tool to estimate placement of APs in a carpeted office space. Most interior walls should be assigned which attenuation value?
A. 2 dB
B. 3 dB
C. 4 dB
D. 5 dB
Answer: B
Q14. Which CLI command is used on a Cisco WLC to troubleshoot mobility, rogue detection, and load-balancing events?
A. debug dot11
B. debug capwap all
C. show dot11 details
D. show capwap details
Answer: A
Q15. What is an interferer that an engineer may see in Cisco CleanAir?
A. microwave ovens
B. rogue APs
C. malicious clients
D. co-channel interference
Answer: A