Cisco 200-601 Free Practice Questions

NEW QUESTION 1
A shutdown in the cookie cutter machine was traced to a broken network cable. What are two reasons that explain why using DLR is an appropriate choice for network resiliency? (Choose two)

• A. DLR is designed for single network operation at the machine level
• B. Moving to a linear topology will reduce the number of cables and so reduce risk of cable failure
• C. DLR is the only resiliency technology that is supported by CIP Safety
• D. Layer 2 resiliency protocols like REP and RSTP do not have a fast enough convergence time for motion control
• E. Half of the network traffic goes clockwise on the ring and the other half counter- clockwise, reducing by 50% the impact of cable failure

Answer: AD

NEW QUESTION 2
Refer to the exhibit.

Which two parameters can be used to diagnose an overloaded system? (Choose two)

• A. Ethernet Port 1 Speed
• B. Module Resource Allocation Actual Rate
• C. Class 3 Received bytes per second
• D. Media Counters Alignment Errors
• E. TCP Connections Active

Answer: BE

NEW QUESTION 3
When troubleshooting a high packet loss condition in the network, the inspection area has an assessed M.I.C.E. value of M=1, I=1, C=3 and E=1. Which condition could be suspect?

• A. Use of shielded Patch Cables, Bonded on one end only.
• B. Use of unshielded Patch Cables.
• C. Broken seal on bulkhead connector.
• D. Oxidation on Shielded RJ45 Patch Plug

Answer: D

NEW QUESTION 4
Which two ports does EtherNet/IP use to communicate? (Choose two.)

• A. TCP 44818
• B. UDP 44818
• C. TCP 502
• D. UDP 502
• E. TCP 2222
• F. UDP 2222

Answer: AF

NEW QUESTION 5
A small manufacturing company has a Class C network address on the plant floor and needs to create five subnets, each accommodating 25 endpoints. Which subnet mask needs to be configured?

• A. 255.255.240.0
• B. 255.255.255.128
• C. 255.255.255.192
• D. 255.255.255.224
• E. 255.255.255.240
• F. 255.255.255.248

Answer: D

NEW QUESTION 6
Exhibit:

Which two statements are correct for a safe wiring installation to the terminal block of the switch or endpoint? (Choose two.)

• A. Insert a green ground wire into the terminal block that is marked RT for return.
• B. Verify that DC power is live and within 24 VDC voltage range before starting wiring.
• C. Verify that the DC power circuit includes an overcurrent protective device that limits the DC current to 5 A.
• D. Because this is a low-voltage DC circuit, anyone can install this wiring without electrical training or qualifications.
• E. Connect the positive 24 VDC conductor to the V terminal and connect the negative 24 VDC return wire to the RT terminal.
• F. A ground wire can optionally be connected to the screw terminal on the front of the switch.

Answer: CE

NEW QUESTION 7
You have been tasked to design an Ethernet network capable of Motion control with cycle times not to exceed 1ms. In order to create a more deterministic network, what characteristic/s should you primarily focus on?

• A. Lattency and Jitter
• B. Redundancy and high availability
• C. Explicit and Implicit messaging
• D. This cycle time is not possible on an Ethernet network
• E. Gigabit port speed

Answer: A

NEW QUESTION 8
Refer to the exhibit. Which lines represent a CIP connection being established between two devices?

• A. 2914 and 2915
• B. 2918 and 2921
• C. 2920 and 2924
• D. 2937 and 2940

Answer: B

NEW QUESTION 9
What security component can be deployed to increase the defense in depth and specifically can be positioned against 'man-in-the-middle' attack?

• A. Deploy 802.1AE
• B. Deploy 802.1X
• C. Deploy 802.1Q
• D. Deploy 802.1AX

Answer: A

NEW QUESTION 10
Which statement is correct regarding ProfiNET communication classes?

• A. ProfiNET-RT traffic is carried in UDP and TCP packets
• B. ProfiNET-NRT is used to carry time critical status information
• C. ProfiNET-IRT requires switches with hardware time scheduling capabilities
• D. ProfiNET-NRT is prioritized as Layer-2 Class-of-Service 1 (CoS 1)

Answer: C

NEW QUESTION 11
Refer to the exhibit.

What issue does this topology present for the represented traffic flow?

• A. Standard Produce/Consume traffic is not suitable for an 802.11 wireless environment.
• B. Only one of the Work Group Bridges can transmit at a time, because 802.11 is half duplex.
• C. The Converged Plant-wide Ethernet best practices for 802.11 wireless don't allow for PAC to PAC traffic.
• D. I/O control traffic should utilize the 2.4 GHz band based on best practices.

Answer: B

NEW QUESTION 12
Refer to the exhibit.

Which values are correct for AP 2 to allow for efficient roaming?

• A. Channel 6, SSID Sittingduck, BSSID 00:0a:0b:0c:0d:0e
• B. Channel 1, SSID Sittingduck, BSSID 00:01:02:03:04:05
• C. Channel 1, SSID Sittingduck, BSSID 00:0a:0b:0c:0d:0e
• D. Channel 6, SSID Sittingduck, BSSID 00:01:02:03:04:05

Answer: A

NEW QUESTION 13
What percentage of an I/O connection would you set the RPI in order to ensure the application has the most current data?

• A. RPI at 50% of IO rate
• B. RPI at 25% of IO rate
• C. PI to 25% of PAC scan rate
• D. Set RPI to 50% of PAC scan rate

Answer: A

NEW QUESTION 14
Refer to the exhibit.

The control system depicted in the exhibit uses VLAN 300 for all of its device ports and PVST is enabled on each switch to switch connection. L2SW4 was inserted between L2SW3 and L2SW5. Links FO2 and FO3 were added and FO1 was disconnected.
Prior to the installation of L2SW4, PanelView was able to communicate with PLC#1. After the change, PLC#1 and PanelView are still able to communicate but neither PLC#1 or PanelView are able to communicate with I/O #1.
L2SW4# show run interfaces FastEthernet 1/1 description I/O#1
switchport access vlan 300 switchport mode access spanning-tree portfast
spanning-tree bpduguard enable
L2SW4# show interfaces trunk
Port Mode Encapsulation Status Native vlan Gi1/1 on 802.1q trunking 1 Gi1/2 on 802.1q trunking 1 Port Vlans allowed on trunk Gi1/1 1,3-9, 301-305,400 Gi1/2 1,3-9, 301-305,400 Port Vlans allowed and active in management domain Gi1/1 1,3-9, 301-305,400 Gi1/2 1,3- 9, 301-305,400 Port Vlans in spanning tree forwarding state and not pruned Gi1/1 1,3-9, 301-305,400 Gi1/2
Based on the output from the switch, what is preventing I/O#1 from communicating with PLC#1 and PanelView?

• A. Interface FastEthernet 1/1 on LWSW4 should be configured as a trunk port
• B. The trunks connecting L2SW4 to L2SW3 and L2SW5 have the wrong encapsulation type
• C. The trunks connecting L2SW4 to L2SW3 and L2SW5 don't allow VLAN 300 traffic
• D. BPDU guard has error-disabled interface FastEthernet 1/1 on LWSW4

Answer: C

NEW QUESTION 15
Which statement is correct regarding Media Redundancy Protocol (MRP) in a ring of ProfiNET devices?

• A. When a link fault is detected, MRP rings must converge in less than 100 milliseconds
• B. MRP defines two device roles, Media Redundancy Master and Media Redundancy Client
• C. MRP can support rings of up to 250 devices
• D. MRP is only supported on network switches

Answer: B

NEW QUESTION 16
Exhibit:

Refer to the exhibit. What are three traffic and interconnection requirements for the devices in the exhibit? (Choose three.)

• A. The EtherNet/IP drive connections are in a high-voltage area and need protection from electromagnetic noise, so shielded cable that is rated for 600 V is advised.
• B. EtherNet/IP devices such as the controller, drive, VoIP phone, and IP camera should be in the same VLAN.
• C. CIP traffic has the highest bandwidth requirement so it needs the highest QoS setting.
• D. EtherNet/IP drive traffic has high sensitivity to random drops, latency, and jitter.
• E. Real-time motion control and VoIP traffic can share the same VLAN with the proper QoS setting.
• F. IEEE1588 and PTP are important for ensuring real-time synchronization.

Answer: ADF

NEW QUESTION 17
AP CAPWAP control traffic should be isolated from wireless client traffic. Which scenario represents the correct configuration to support the SSIDs of this controller-based access point in FlexConnect local switching mode?

• A. [MISSING]
• B. [MISSING]
• C. [MISSING]
• D. [MISSING]

Answer: C

NEW QUESTION 18
Which in-depth approach is used when deploying defense in an industrial zone?

• A. Use PLCs and control systems from multiple vendors in such a way that the process will become resilient for failures of one vendor.
• B. Deploy two factor authentications for all operators which need to login remote while working from home.
• C. Collect log files at a central location for easy back-up and encryption to provide privacy.
• D. Create multiple zones in the industrial zone and protect / inspect traffic between the zones with firewalls and intrusion monitors.

Answer: D

NEW QUESTION 19
Which statement is true regarding ProfiSAFE?

• A. ProfiSAFE traffic must be carried on a network that is physically separated from automation traffic
• B. ProfiSAFE relies on the error detection mechanisms of Ethernet and TCP/IP to determine if there are network errors
• C. ProfiSAFE can be used in safety applications up to Safety Integrity Level 3 (SIL3)
• D. ProfiSAFE is only used by ProfiBUS PA and ProfiBUS DA devices

Answer: C

NEW QUESTION 20
Which configuration enables an Industrial Ethernet switch to participate in PTP clock selection and sets the priority value that would break the tie between switches with matching default criteria to 50?

• A. ptp mode boundary ptp priority1 10ptp priority2 50
• B. ptp mode boundary ptp priority1 50ptp priority2 10
• C. ptp mode e2etransparent ptp priority1 50ptp priority2 10
• D. ptp mode e2etransparent ptp priority1 10ptp priority2 50

Answer: A

NEW QUESTION 21
......