Introducing The New!
Surepassexam Collection
Get Unlimited Access to all
Surepassexam's PREMIUM files
Q1. A network engineer wants to automate the monitoring of Cisco TelePresence TX systems. Which step should the engineer take first?
A. Configure Cisco TMS on the codec.
B. Configure Medianet on the codec.
C. Configure NTP on the codec.
D. Configure Multiway on the codec.
E. Configure SNMP on the codec.
Answer: E
Q2. A network engineer is setting up a Cisco TelePresence Content Server. The customer requires live streaming, but does not have a streaming server. Which media should be configured to stream locally from the TelePresence Content Server?
A. QuickTime
B. MPEG-4
C. Flash
D. Windows Media
E. Darwin
Answer: D
Q3. A Unified Communications engineer wants to configure a Cisco TelePresence SX endpoint
using static IP addressing to use a different TFTP server. Which path will allow the engineer to complete this configuration?
A. Network Services > Network 1 > DHCP RequestTFTPServerAddress > Off
B. Network > TFTP > DHCP RequestTFTPServerAddress > Off
C. Network Services > TFTP > DHCP RequestTFTPServerAddress > Off
D. Configuration > System Configuration > Provisioning > Set the External Manager Address
Answer: D
Q4. Which two of these are considered to be provisioning and scheduling management tools in a Cisco TelePresence environment? (Choose two.)
A. Cisco TelePresence Manager
B. Cisco Video Surveillance Operations Manager
C. Cisco TelePresence Management Suite
D. Cisco TelePresence Multipoint Control Unit
E. Cisco Video Surveillance Management Server
Answer: A,C
Q5. How would an administrator reset a Cisco VCS Control appliance to the default configuration?
A. Via the CLI, log in as root and issue the factory-reset command.
B. Via the CLI, log in as root and issue the reset-defaults command.
C. Via the web GUI, log in as the administrator, choose Backup and Restore, and click the Factory Reset button.
D. Hold down the power button for 10 seconds until the light flashes.
E. Hold down the reset button on the back of the appliance for 10 seconds.
Answer: A
Q6. When scheduling a multipoint conference, which three devices are required for the conference to be scheduled and completed successfully? (Choose three.)
A. Cisco Unified Communications Manager
B. multipoint control unit
C. video conferencing endpoints
D. Cisco Unity Connection
E. Cisco Unified IM and Presence
Answer: A,B,C
Q7. Which MCU supports the use of a lobby screen?
A. CTMS
B. TS 8710
C. MCU 5300
D. Conductor
Answer: B
Q8. You have installed a C-Series endpoint in an office where DHCP is not supported. At a minimum, which four network items must be configured for the endpoint to be able to register with H.323 on a Cisco TelePresence Video Communication Server located at the external headquarters location? (Choose four.)
A. unique IPv4 address
B. subnet mask
C. default gateway
D. Cisco VCS IPv4 address
E. Active Directory IPv4 address
F. SMTP server IPv4 address
Answer: A,B,C,D
Q9. Which two layout or switching modes are supported with the Cisco TelePresence Multipoint Switch? (Choose two.)
A. enhanced continuous presence
B. active speaker switching
C. continuous presence
D. speaker switching
E. room switching
F. active continuous presence
Answer: D,E
Q10. Which of these needs to be enabled in Cisco Unified Communications Manager in order for the Cisco TelePresence System 500-32 to be able to share a presentation with a Cisco TelePresence System Codec C40 endpoint that is registered to a VCS?
A. Allow iX application media
B. Send send-receive SDP in mid-call invite
C. Allow presentation sharing using BFCP
D. Allow presentation sharing using H.235
E. Deliver conference bridge identifier
Answer: C
Q11. Which Cisco TelePresence Multipoint Control Unit Layout view mode gives prominence to one conference participant over the other conference participants while still allowing conference participants to view multiple participants at the same time?
A. enhanced continuous presence
B. active speaker
C. continuous presence
D. room switching
E. speaker switching
Answer: A
Q12. Refer to the exhibit.
You have just finished installing a 65-inch dual profile system in a multipurpose room. After powering up the entire system, only one display is used. Using the information in the exhibit, why is the second display not displaying anything from the system?
A. The Cisco TelePresence profile systems do not support dual display.
B. The display is not powered on.
C. The dual display option key has not been input into the codec.
D. The codec has the appropriate option keys installed, so either the display is not cabled correctly, the codec is configured incorrectly, or there is no input being sent to the display.
Answer: D
Q13. In this item, you will need to use all information presented to you to successfully answer the question.
Refer to the exhibits. An administrator needs to perform a factory reset on a C-Series endpoint. What are two valid ways to accomplish this task? (Choose two.)
A. Exhibit A
B. Exhibit B
C. Exhibit C
D. Exhibit D
E. Exhibit E
Answer: C,D
Q14. Which codec is most suitable for a video streaming solution?
A. AAC-LD
B. G.729
C. H.264
D. G.711
Answer: C
Q15. Refer to the exhibit.
The customer recently connected a new TV monitor to the Cisco TelePresence endpoint. This device is now showing a warning concerning the echo cancellation delay. Which action could help mitigate this issue?
A. Turn off any postprocessing settings.
B. Turn off 3D mode on the new TV.
C. Turn on Frequency Scan Acceleration for the new TV.
D. Turn off surround sound on the new TV.
Answer: A