Introducing The New!
Surepassexam Collection
Get Unlimited Access to all
Surepassexam's PREMIUM files
Q1. Which four call coverage features are used by voice gateways? (Choose four.)
A. call hunt
B. Call Park
C. Call Pickup
D. call redirecting
E. overlaid phone-dn
F. basic automatic call distribution
G. overlaid ephone-dn
H. basic manual call distribution
Answer: A,C,F,G
Q2. Which two features are advantages of deploying a cluster over WAN? (Choose two.)
A. Shared line appearances
B. CentralizedDSP resources
C. Extension mobility within the cluster
D. Scalability up to 20 sites, if thereis sufficient IP WAN bandwidth
E. Failover to co-resident Cisco UnifiedCall Manager Express platforms
Answer: A,C
Q3. What is the difference between policing and shaping?
A. Policing: Transmit and mark, then transmit the packets. Shaping: Buffer the exceeding packets.
B. Policing: Transmit the packets. Shaping: Buffer the exceeding packets.
C. Policing: Transmit, drop or mark, then transmit the packets. Shaping: Buffer the exceeding packets.
D. Policing: Buffer the exceeding packets. Shaping: Transmit and mark, then transmit the packets.
Answer: C
Explanation: Reference:
http://www.cisco.com/c/en/us/support/docs/quality-of-service-qos/qos-policing/19645-policevsshape.html
Q4. Where do you configure the region for a group of devices?
A. Common device profile.
B. Device defaults.
C. Common device configuration.
D. Common phone profile.
E. Device pool.
Answer: E
Explanation: Reference:
Page 73
Cisco Unified Communications Manager Administration Guide, Release 10.0(1)
Q5. When implementing a global dial plan, which digit manipulation feature in CUCM does Ciscorecommend for adding +1 to all outbound calls?
A. Called party transformation.
B. Calling party transformation.
C. Translation pattern.
D. External phone mask.
Answer: A
Q6. You are a Voice Engineer at ABC Company. You want to provision a new voice gateway for a remotesite, and you need to configure 24 channels of a T1 CAS interface. Which set is the correct set ofcommands for this configuration?
A. R1(config)# controller t1 1/0
R1(config-controller)# framing esf
R1(config-controller)# linecode b8zs
R1(config-controller)# primary-group 1 timeslot 1-24 type fxo-loop-start
B. R1(config)# controller t1 1/0
R1(config-controller)# linecode hdb3
R1(config-controller)# framing crc4
R1(config-controller)# clock source line
R1(config-controller)# ds0-group 1 timeslot 1-24 type fxo-loop-start
C. R1(config)# isdn switch-type primary-5ess
R1(config)# controller t1 t1/0
R1(config-controller)# pri-group timeslots 1-24
D. R1(config)# controller t1 1/0
R1(config-controller)# framing esf
R1(config-controller)# linecode b8zs
R1(config-controller)# clock source line
R1(config-controller)# ds0-group 1 timeslot 1-24 type fxo-loop-start
Answer: D
Explanation: Reference:
Page 9-11 http://www.cisco.com/c/en/us/td/docs/ios/voice/isdn/configuration/guide/12_4t/vi_12_4t_bo ok/
vi_imp_t1cas_voip.pdf
Q7. Which four software based media resources require that the Cisco IP voice media streamApplicationbe activated?
A. MOH.
B. SIP.
C. H.323 Gateways.
D. Annunciator.
E. Gatekeeper.
F. MTP.
G. Audio conferencing.
Answer: A,D,F,G
Q8. On Cisco Unified Communications Manager, where can you change the softkey templates from your IPphone?
A. Cisco Unified Communications Manager Serviceability > Device > Device Settings > Softkey Templates.
B. Cisco Unified Communications Manager Administration > Device > Device Settings > Softkey Templates.
C. Cisco Unified Communications Manager Administration > Device > Device Settings > Phone ButtonTemplate.
D. Cisco Unified Communications Manager Administration > Device > Device Settings > Device Defaults.
Answer: B
Explanation: Reference:
Page 726, 731
Cisco Unified Communications Manager Administration Guide, Release 10.0(1)
Q9. Which three CLI commands allow you to verify the correct VoIP dial-peer matching? (Choose three.)
A. debug ccsip messages
B. debug voip ccapi inout
C. debug dialpeer match
D. debug voip dialpeer inout
E. show dialplan number
Answer: B,D,E
Q10. When comparing SIP H.323 and MGCP, which of the following is specific to SIP?
A. The dial plan is directly on the gateway.
B. SIP provides support for third-party entities.
C. SIP defines Translation per the gateway.
D. SIP has a centralized dial plan.
Answer: B
Q11. If you have configured translation rules, what command do you use to verify digit manipulation?
A. execute translation-rule
B. show translation-rule
C. test translation-rule
D. debug translation-rule
E. set translation-rule
Answer: C
Explanation:
If you have configured translation rules, use the test translation-rule command to verify digitmanipulation. Page 136.
Reference:
http://www.cisco.com/c/en/us/td/docs/ios/12_2/voice/configuration/guide/fvvfax_c/vvfpeers. pdf
Q12. Refer to the exhibit.
What is the command to place the static IP address by CLI in the CiscoTelePresence MSE 8000?
A. MSE 8050: static 0 10.10.2.13 255.255.255.255 10.10.2.1 200.87.100.10 200.87.100.20.
B. MSE 8050: static 0 10.10.2.13 255.255.255.0 10.10.2.1 200.87.100.10 200.87.100.20.
C. MSE 8050: static 1 10.10.2.13 255.255.255.0 10.10.2.1 200.87.100.10 200.87.100.20.
D. MSE 8050: static ip 0 10.10.2.13 255.255.255.0 10.10.2.1 200.87.100.10 200.87.100.20.
Answer: B
Q13. Which QoS model is bandwidth-dedicated to provide sufficient quality for applications that need highresolution, such as video terminals?
A. Best-Effort
B. IntServ
C. DiffServ
D. DiffServf
Answer: C
Q14. By default, what value is voice traffic marked as on a Cisco Catalyst Switch?
A. DSCP EF value 46, Cos 5.
B. DSCP EF value 46, Cos 7.
C. DSCP CAS6 value 21, Cos 3.
D. DSCP AF21, Cos 5.
Answer: A
Q15. Which parameter is required on MCU for ad hoc conferencing?
A. Media Port reservation
B. incoming calls to unknown conferences or auto-attendants
C. DSP reservation for video
D. MCU type
E. MCU Conference Bridge SIP Port
Answer: A