Cisco 300-075 Free Practice Questions

Q1. Refer to the exhibit. 

How does the Cisco Unified Communications Manager advertise dn-block 1? 

A. 4XXX and the ToDID will 0: 

B. 4XXX and the ToDID will 0:1972555 

C. 4XXX 

D. 4XXX and the ToDID will 0:+ 1972555 

E. 19725554XXX 

View Answer

Q2. You recently implemented call redundancy at a new remote site, and users report that calls are dropped when the remote site supposedly is in SRST. Which two actions must you take to troubleshoot the problem? (Choose two.) 

A. Confirm that SRST is configured on the voice gateway. 

B. Confirm that the site has an SRST reference that is correctly associated with the Cisco Unified Communications Manager group. 

C. Confirm that a calling search space is assigned to the voice gateway in Cisco Unified Communications Manager. 

D. Confirm that the site devices are associated with a Cisco Unified Communications Manager group and that four Cisco Unified Communications Manager servers are available. 

E. Check the Region settings in Cisco Unified Communications Manager. 

F. Restart Cisco Unified Communications Manager services to confirm that the server is working correctly. 

View Answer

Q3. Which device is needed to integrate H.320 into the Cisco video solution? 

A. video gateway 

B. MGCP gateway 

C. H.323 gatekeeper 

D. MCU 

View Answer

Q4. Which action configures phones in site A to use G.711 to site B but to use G.729 to site C? 

A. Configure Cisco Unified Communications Manager regions. 

B. Configure Cisco Unified Communications Manager locations. 

C. Configure transcoder resources in Cisco Unified Communications Manager. 

D. Configure a gatekeeper. 

View Answer

Q5. Refer to the exhibit. 

Assume that the HQ phones have access to the HQ partition, and BR phones have access to the BR partition. Which set of implementations would best address the overlapping directory number extensions for intersite (WAN) calling between the HQ site and the BR site? 

A. Configure a route pattern 8222.[12]XXX for site HQ, and assign it to partition HQ. Configure the called party DDI of Predot.Configure a route pattern for site BR 8111.[1-3]XXX, and assign it to partition BR. Configure called party DDI Predot.Use the local gateway at each site. Prefix the appropriate site code for the calling number. 

B. Configure a single route pattern for both sites 8[12,12,12].[1-32]XXX. Use a route list that contains the local route group for each site. Prefix the appropriate site code for the calling number. 

C. Configure a translation pattern 8222.[12]XXX for site HQ, and assign it to partition HQ. Use a CSS that contains the partitions for BR phones.Configure a translation pattern 8111.[1-3]XXX for site BR, and assign it to partition BR. Use a CSS that contains the partitions for HQ phones.For both translation patterns, configure the called party DDI of Predot. Prefix the appropriate site code for the calling number. 

D. Configure a translation pattern 8222.[12]XXX for site HQ, and assign it to partition BR. Use a CSS that contains the partitions for HQ phones.Configure a translation pattern 8111.[1-3]XXX for site BR, and assign it to partition HQ. Use a CSS that contains the partitions for BR phones.For both translation patterns, configure the called party DDI of Predot. Prefix the appropriate site code for the calling number. 

View Answer

Q6. Which two options for a Device Mobility-enabled IP phone are true? (Choose two.) 

A. The phone configuration is not modified. 

B. The roaming-sensitive parameters of the current (that is, the roaming) device pool are applied. 

C. The user-specific settings determine which location-specific settings are downloaded from the Cisco Unified Communications Manager device pool. 

D. If the DMGs are the same, the Device Mobility-related settings are also applied. 

View Answer

Q7. Which technologies provide remote-site redundancy for Cisco IP Phones during a WAN failure? 

A. SRST and MGCP fallback 

B. SRST and TEHO 

C. TEHO and MGCP fallback 

D. SRST and AAR 

View Answer

Q8. Which Cisco IOS command is used to verify that a SAF Forwarder that is registered with Cisco Unified Communications Manager has established neighbor relations with an adjacent SAF Forwarder? 

A. show eigrp service-family ipv4 neighbors 

B. show eigrp address-family ipv4 neighbors 

C. show voice saf dndball 

D. show saf neighbors 

E. show ip saf neighbors 

View Answer

Q9. Which system configuration is used to set audio codecs? 

A. region 

B. location 

C. physical location 

D. licensing 

View Answer

Q10. When implementing a dial plan for multisite deployments, what must be present for SRST to work successfully? 

A. dial peers that address all sites in the multisite cluster 

B. translation patterns that apply to the local PSTN for each gateway 

C. incoming and outgoing COR lists 

D. configuration of the gateway as an MGCP gateway 

View Answer

Q11. Refer to the exhibit. 

The H.323 Gateway is showing status “unknown”. Which statement is true? 

A. The gateway must be reset in Cisco Unified Communications Manager. 

B. The no gateway command followed by the gateway command must be issued in Cisco IOS. 

C. The mgcp commands must be removed. 

D. H.323 gateways do not register with Cisco Unified Communications Manager H.323 gateways always show status "Unknown". 

E. VUAN 1 20 may be down and so the H.323 gateway appears offline to the Cisco Unified Communications Manager 

View Answer

Q12. Which two statements regarding you configuring a traversal server and traversal client relationship are true? (Choose two.) 

A. VCS supports only the H.460.18/19 protocol for H.323 traversal calls. 

B. VCS supports either the Assent or the H.460.18/19 protocol for H.323 traversal calls. 

C. VCS supports either the Assent or the H.460.18/19 protocol for SIP traversal calls. 

D. If the Assent protocol is configured, a TCP/TLS connection is established from the traversal client to the traversal server for SIP signaling. 

E. A VCS Expressway located in the public network or DMZ acts as the firewall traversal client. 

View Answer

Q13. Refer to the exhibit. 

The exhibit shows centralized Cisco Unified Communications Manager configuration components for TEHO calls to U.S. area code 408 from the U.K. The PSTN access code for the U.K. is 9 and 001 for international calls to the U.S. To match the US-TEHO pattern \+!, how should the translation pattern be configured? 

A. 9001.4085551234 with the Called Party Transformation:Discard Digits PreDotPrefix Digits Outgoing Calls: + 

B. 9.0014085551234 with the Called Party Transformation:Discard Digits PreDotPrefix Digits Outgoing Calls: +1 

C. 900.14085551234 with the Called Party Transformation:Discard Digits PreDotPrefix Digits Outgoing Calls: +1 

D. 900.14085551234 with the Called Party Transformation:Discard Digits PreDotPrefix Digits Outgoing Calls: + 

E. 001.4085551234 with the Called Party Transformation:Prefix Digits Outgoing Calls: + 

View Answer

Q14. The relationship between a Region and a Location is that the Region codec parameter is used between a Region and its configured Locations. 

A. TRUE 

B. FALSE 

View Answer

Q15. Refer to the exhibit. 

When a user presses a speed dial to +442079460255 when the SAF network is down, which event should occur? 

A. The call will reroute via the PSTN with the constructed PSTN number as 442079460255. 

B. The call will reroute via the PSTN with the constructed PSTN number as +442079460255. 

C. The call will reroute via the PSTN with the constructed PSTN number as 00442079460255. 

D. The call will fail because the ToDID is 0:. 

E. The call will fail because the called number will be 2079460255. 

View Answer