Cisco 300-101 Free Practice Questions

Question No: 5

A network engineer finds that a core router has crashed without warning. In this situation, which feature can the engineer use to create a crash collection?

A. secure copy protocol

B. core dumps

C. warm reloads

D. SNMP

E. NetFlow

View Answer

Question No: 6

Which keyword of the aaa authentication ppp command supports PAP only?

A. line

B. krb5

C. local

D. local-case

E. enable

View Answer

Question No: 7

Refer to the exhibit.

After you apply this configuration to router R1, it fails to establish an eBGP neighbour relationship with R2. Which action do you take to correct the problem?

A. Configure the update-source for 10.1.1.2

B. Change the ebgp-multihop value to 1.

C. Add the no synchronization statement at the end of the configuration.

D. Replace the maximum-paths command at the end of the configuration with maximum- paths ibgp 4 import 2.

View Answer

Question No: 8

Which value does a point-to-point GRE tunnel use to identify a peer?

A. MAC address

B. configured multicast address.

C. DLCI

D. IP address

E. VC ID

View Answer

Question No: 9

Which statement about the use of tunneling to migrate to IPv6 is true?

A. Tunneling is less secure than dual stack or translation.

B. Tunneling is more difficult to configure than dual stack or translation.

C. Tunneling does not enable users of the new protocol to communicate with users of the old protocol without dual-stack hosts.

D. Tunneling destinations are manually determined by the IPv4 address in the low-order 32 bits of IPv4-compatible IPv6 addresses.

View Answer

Question No: 10

Which two configurations can a PPPoE client support? (Choose Two)

A. Eight clients are configured on a single CPE.

B. The client is connected to multiple hosts over DMVPN

C. The client is installed on the same network device as the server.

D. The client is connecting over an ATM PVC

E. The client is installed on a native IPv6 network.

View Answer

Question No: 11

What does the following access list, which is applied on the external interface FastEthernet 1/0 of the perimeter router, accomplish?

router(config)#access-list 101 deny ip 10.0.0.0 0.255.255.255 any log

router (config)#access-list 101 deny ip 192.168.0.0 0.0.255.255 any log

router (config)#access-list 101 deny ip 172.16.0.0 0.15.255.255 any log router (config)#access-list 101 permit ip any any

router (config)#interface fastEthernet 1/0 router (config-if)#ip access-group 101 in

A. It prevents incoming traffic from IP address ranges 10.0.0.0-10.0.0.255, 172.16.0.0- 172.31.255.255, 192.168.0.0-192.168.255.255 and logs any intrusion attempts.

B. It prevents the internal network from being used in spoofed denial of service attacks and logs any exit to the Internet.

C. It filters incoming traffic from private addresses in order to prevent spoofing and logs any intrusion attempts.

D. It prevents private internal addresses to be accessed directly from outside.

View Answer

Question No: 12

Based on the configuration command below, which statement is true? Router(config)#service timestamps log datetime msec

A. All IOS services will indicate the date and time when the service was started.

B. All syslog messages that are generated will indicate the date and time when the event occurred.

C. All IOS services will indicate the date and time when the service was last used.

D. All high-priority syslog messages that are generated will indicate the date and time when the event occurred.

View Answer

Question No: 13

What is the default maximum segment size for TCP traffic?

A. 536

B. 1492

C. 1500

D. 1508

E. 3340

F. 4096

View Answer

Question No: 14

Exhibit:

=================

AS65000 (R1)u2014(R2)u2013 (R3)

| |

| |

(R4) (R5)

| |

10.1.0.0/16 10.2.0.0/16

AS 65001 AS65002 Second | should be between R3 and R5

==================

Refer to exhibit. If the IGP in AS65000 is RIPv2, which networks are displayed when you enter show ip route on router R2?

A. VLSM subnts in 10.0.0.0/16 and the major network 10.2.0.0/16 only

B. VLSM subnets in 10.0.0.0/16 and the major network 10.2.0.0/16 only

C. VLSM subnets in 10.0.0.0/16 only

D. major networks 10.1.0.0/16 and 10.2.0.0/16 only

E. VLSM subnets in 10.0.0.0/16 and the major networks 10.1.0.0/16 10.2.0.0/16

View Answer