300-101 Premium Bundle

300-101 Premium Bundle

ROUTE Implementing Cisco IP Routing Certification Exam

4.5 
(42870 ratings)
0 QuestionsPractice Tests
0 PDFPrint version
November 21, 2024Last update

Cisco 300-101 Free Practice Questions

P.S. Breathing 300-101 testing engine are available on Google Drive, GET MORE: https://drive.google.com/open?id=1g4kPItyKIZuA3JfCSZX112aKL18D2zfl


New Cisco 300-101 Exam Dumps Collection (Question 14 - Question 23)

Question No: 14

Which three statements about SNMP are true? (Choose Three)

A. The manager configures and send traps to the agent.

B. The manager sends GET and SET messages.

C. SNMPv3 supports authentication and encryption.

D. The manager polls the agent using UDP port 161

E. The MIB database can be altered only by the SNMP agent.

F. The agent is the monitoring device.

Answer: C,D,F


Question No: 15

Which encapsulation supports an interface that is configured for an EVN trunk?

A. 802.1Q

B. ISL

C. PPP

D. Frame Relay

E. MPLS

F. HDLC

Answer: A


Question No: 16

What is the purpose of the autonomous-system {autonomous-system-number} command?

A. It sets the EIGRP autonomous system number in a VRF.

B. It sets the BGP autonomous system number in a VRF.

C. It sets the global EIGRP autonomous system number.

D. It sets the global BGP autonomous system number.

Answer: A


Question No: 17

A network engineer is configuring a routed interface to forward broadcasts of UDP 69, 53, and 49 to 172.20.14.225. Which command should be applied to the configuration to allow this?

A. router(config-if)#ip helper-address 172.20.14.225

B. router(config-if)#udp helper-address 172.20.14.225

C. router(config-if)#ip udp helper-address 172.20.14.225

D. router(config-if)#ip helper-address 172.20.14.225 69 53 49

Answer: A


Question No: 18

Refer to the exhibit.

Which command only announces the 1.2.3.0/24 network out of FastEthernet 0/0?

A. distribute list 1 out

B. distribute list 1 out FastEthernet0/0

C. distribute list 2 out

D. distribute list 2 out FastEthernet0/0

Answer: D


Question No: 19

Which three steps are most helpful in verifying proper route redistribution? (Choose three.)

A. On the routers not performing the route redistribution, use the show ip route command to see if the redistributed routes show up.

B. On the ASBR router performing the route redistribution, use the show ip protocol command to verify the redistribution configurations.

C. On the ASBR router performing the route redistribution, use the show ip route command to verify that the proper routes from each routing protocol are there.

D. On the routers not performing the route redistribution, use the show ip protocols command to verify the routing information sources.

E. On the routers not performing the route redistribution, use the debug ip routing command to verify the routing updates from the ASBR.

Answer: A,B,C

Explanation:

In order to verify proper route redistribution, use the u201cshow ip routeu201d command on all routers within the network, as well as the ABSR, to verify that the routes are properly being advertised to all routers. In addition, issuing the u201cshow ip protocolu201d can be used on the router performing the redistribution to verify that routes are being redistributed into each other.


Question No: 20

Which command should be added to RTB under router bgp 100 to allow only the external OSPF routes to be redistributed to RTC?

A. redistribute ospf 1

B. redistribute ospf 1 match external 1

C. redistribute ospf 1 match external 2

D. redistribute ospf 1 match external 1 external 2

Answer: D

Explanation:

Use the external keyword along with the redistribute command under router bgp to redistribute OSPF external routes into BGP. With the external keyword, you have three choices: 1. redistribute both external type-1 and type-2 (Default) 2. redistribute type-1 3. redistribute type-2 Enter the commands in the configuration mode as described here: RTB(config-router)# router bgp 100 RTB(config-router)# redistribute ospf 1 match external.


Question No: 21

CORRECT TEXTROUTE.com is a small IT corporation that has an existing enterprise network that is running IPv6 0SPFv3. Currently OSPF is configured on all routers. However, R4's loopback address (FEC0:4:4) cannot be seen in R1's IPv6 routing table. You are tasked with identifying the cause of this fault and implementing the needed corrective actions that uses OPSF features and does not change the current area assignments. You will know that you have corrected the fault when R4's loopback address (FEC0:4:4) can be seen in RTs IPv6 routing table.

Special Note: To gain the maximum number of points you must remove all incorrect or unneeded configuration statements related to this issue.

Answer:

Here is the solution below:

Explanation:

To troubleshoot the problem, first issue the show running-config on all of 4 routers. Pay more attention to the outputs of routers R2 and R3 The output of the "show running-config" command of R2:

The output of the "show running-config" command of R3:

We knew that all areas in an Open Shortest Path First (OSPF) autonomous system must be physically connected to the backbone area (Area 0). In some cases, where this is not possible, we can use a virtual link to connect to the backbone through a non-backbone area. The area through which you configure the virtual link is known as a transit area. In this case, the area 11 will become the transit area. Therefore, routers R2 and R3 must be configured with the area <area id> virtual-link <neighbor router-id>command. + Configure virtual link on R2 (from the first output above, we learned that the OSPF process ID of R2 is 1):

R2>enable R2#configure terminal

R2(config)#ipv6 router ospf 1

R2(config-rtr)#area 11 virtual-link 3.3.3.3 Save the configuration:

R2(config-rtr)#end

R2#copy running-config startup-config

(Notice that we have to use neighbor router-id 3.3.3.3, not R2's router-id 2.2.2.2) + Configure virtual link on R3 (from the second output above, we learned that the OSPF process ID of R3 is 1 and we have to disable the wrong configuration of "area 54 virtual-link 4.4.4.4"):

R3>enable R3#configure terminal

R3(config)#ipv6 router ospf 1

R3(config-rtr)#no area 54 virtual-link 4.4.4.4

R3(config-rtr)#area 11 virtual-link 2.2.2.2 Save the configuration:

R3(config-rtr)#end

R3#copy running-config startup-config

You should check the configuration of R4, too. Make sure to remove the incorrect configuration statements to get the full points.

R4(config)#ipv6 router ospf 1

R4(config-router)#no area 54 virtual-link 3.3.3.3 R4(config-router)#end

After finishing the configuration doesnu2021t forget to ping between R1 and R4 to make sure they work.

Note. If you want to check the routing information, use the show ipv6 route command, not "show ip route".


Question No: 22

Refer to the exhibit.

Based on this FIB table, which statement is correct?

A. There is no default gateway.

B. The IP address of the router on FastEthernet is 209.168.201.1.

C. The gateway of last resort is 192.168.201.1.

D. The router will listen for all multicast traffic.

Answer: C


Question No: 23

Refer to exhibit.

A user calls from another branch office with a request to establish a simple VPN tunel to test a new routeru2021s tunneling capability Based on the configuration in the exhibit, which type of tunnel was configured?

A. PPTP

B. IPsec site-to-site

C. 6to4

D. EZVPN

Answer: B


Recommend!! Get the Breathing 300-101 dumps in VCE and PDF From Surepassexam, Welcome to download: https://www.surepassexam.com/300-101-exam-dumps.html (New 487 Q&As Version)


START 300-101 EXAM