Introducing The New!
Surepassexam Collection
Get Unlimited Access to all
Surepassexam's PREMIUM files
Q1. Which command globally enables AAA on a device?
A. aaa new-model
B. aaa authentication
C. aaa authorization
D. aaa accounting
Answer: A
Q2. Interface FastEthernet0/1 is configured as a trunk interface that allows all VLANs. This command is configured globally:
monitor session 2 filter vlan 1 - 8, 39, 52
What is the result of the implemented command?
A. All VLAN traffic is sent to the SPAN destination interface.
B. Traffic from VLAN 4 is not sent to the SPAN destination interface.
C. Filtering a trunked SPAN port effectively disables SPAN operations for all VLANs.
D. The trunk's native VLAN must be changed to something other than VLAN 1.
E. Traffic from VLANs 1 to 8, 39, and 52 is replicated to the SPAN destination port.
Answer: E
Q3. After UDLD is implemented, a Network Administrator noticed that one port stops receiving UDLD packets. This port continues to reestablish until after eight failed retries. The port then transitions into the errdisable state. Which option describes what causes the port to go into the errdisable state?
A. Normal UDLD operations that prevent traffic loops.
B. UDLD port is configured in aggressive mode.
C. UDLD is enabled globally.
D. UDLD timers are inconsistent.
Answer: B
Q4. Which switch feature prevents traffic on a LAN from being overwhelmed by continuous multicast or broadcast traffic?
A. storm control
B. port security
C. VTP pruning
D. VLAN trunking
Answer: A
Q5. A new network that consists of several switches has been connected together via trunking interfaces. If all switches currently have the default VTP domain name "null", which statement describes what happens when a domain name is configured on one of the switches?
A. The switch with the non-default domain name restores back to "null" upon reboot.
B. Switches with higher revision numbers does not accept the new domain name.
C. VTP summary advertisements are sent out of all ports with the new domain name.
D. All other switches with the default domain name become VTP clients.
Answer: C
Q6. If a network engineer applies the command mac-address-table notification mac-move on a Cisco switch port, when is a syslog message generated?
A. A MAC address or host moves between different switch ports.
B. A new MAC address is added to the content-addressable memory.
C. A new MAC address is removed from the content-addressable memory.
D. More than 64 MAC addresses are added to the content-addressable memory.
Answer: A
Q7. An administrator recently configured all ports for rapid transition using PortFast. After testing, it has been determined that several ports are not transitioning as they should. What is the reason for this?
A. RSTP has been enabled per interface and not globally.
B. The STP root bridge selection is forcing key ports to remain in non-rapid transitioning mode.
C. STP is unable to achieve rapid transition for trunk links.
D. The switch does not have the processing power to ensure rapid transition for all ports.
Answer: C
Q8. Which SDM template is the most appropriate for a Layer 2 switch that provides connectivity to a large number of clients?
A. VLAN
B. default
C. access
D. routing
Answer: A
Q9. Refer to the exhibit.
A network engineer investigates a recent network failure and notices that one of the interfaces on the switch is still down. What is causing the line protocol on this interface to be shown as down?
A. There is a layer 1 physical issue.
B. There is a speed mismatch on the interface.
C. The interface is configured as the target of the SPAN session.
D. The interface is configured as the source of the SPAN session.
E. There is a duplex mismatch on the interface.
Answer: C
Q10. A network is running VTPv2. After verifying all VTP settings, the network engineer notices that the new switch is not receiving the list of VLANs from the server. Which action resolves this problem?
A. Reload the new switch.
B. Restart the VTP process on the new switch.
C. Reload the VTP server.
D. Verify connected trunk ports.
Answer: D
Q11. A network engineer changed the port speed and duplex setting of an existing EtherChannel bundle that uses the PAgP protocol. Which statement describes what happens to all ports in the bundle?
A. PAgP changes the port speed and duplex for all ports in the bundle.
B. PAgP drops the ports that do not match the configuration.
C. PAgP does not change the port speed and duplex for all ports in the bundle until the switch is rebooted.
D. PAgP changes the port speed but not the duplex for all ports in the bundle.
Answer: A
Q12. What is the maximum number of VLANs that can be assigned to an access switchport without a voice VLAN?
A. 0
B. 1
C. 2
D. 1024
Answer: B
Q13. Refer to the exhibit.
What is the result of the configuration?
A. The EtherChannels would not form because the load-balancing method must match on the devices.
B. The EtherChannels would form and function properly even though the load-balancing and EtherChannel modes do not match.
C. The EtherChannels would form, but network loops would occur because the load- balancing methods do not match.
D. The EtherChannels would form and both devices would use the dst-ip load-balancing method because Switch1 is configured with EtherChannel mode active.
Answer: B
Q14. Which two protocols can be automatically negotiated between switches for trunking? (Choose two.)
A. PPP
B. DTP
C. ISL
D. HDLC
E. DLCI
F. DOT1Q
Answer: C,F
Q15. The command storm-control broadcast level 75 65 is configured under the switch port connected to the corporate mail server. In which three ways does this command impact the traffic? (Choose three.)
A. SNMP traps are sent by default when broadcast traffic reaches 65% of the lower-level threshold.
B. The switchport is disabled when unicast traffic reaches 75% of the total interface bandwidth.
C. The switch resumes forwarding broadcasts when they are below 65% of bandwidth.
D. Only broadcast traffic is limited by this particular storm control configuration.
E. Multicast traffic is dropped at 65% and broadcast traffic is dropped at 75% of the total interface bandwidth.
F. The switch drops broadcasts when they reach 75% of bandwidth.
Answer: CDF
Q16. Refer to the exhibit.
A multilayer switch has been configured to send and receive encapsulated and tagged frames. VLAN 2013 on the multilayer switch is configured as the native VLAN. Which option is the cause of the spanning-tree error?
A. VLAN spanning-tree in SW-2 is configured.
B. spanning-tree bpdu-filter is enabled.
C. 802.1q trunks are on both sides, both with native VLAN mismatch.
D. VLAN ID 1 should not be used for management traffic because its unsafe.
Answer: C
Q17. Pilot testing of the new switching infrastructure finds that when the root port is lost, STP immediately replaces the root port with an alternative root port. Which spanning-tree technology is used to accomplish backup root port selection?
A. PVST+
B. PortFast
C. BackboneFast
D. UplinkFast
E. Loop Guard
F. UDLD
Answer: D