Introducing The New!
Surepassexam Collection
Get Unlimited Access to all
Surepassexam's PREMIUM files
Q1. Which technique allows specific VLANs to be strictly permitted by the administrator?
A. VTP pruning
B. transparent bridging
C. trunk allowed VLANs
D. VLAN access-list
E. L2P tunneling
Answer: C
Q2. What is the maximum number of switches that can be stacked using Cisco StackWise?
A. 4
B. 5
C. 8
D. 9
E. 10
F. 13
Answer: D
Q3. A network engineer configures port security and 802.1x on the same interface. Which option describes what this configuration allows?
A. It allows port security to secure the MAC address that 802.1x authenticates.
B. It allows port security to secure the IP address that 802.1x authenticates.
C. It allows 802.1x to secure the MAC address that port security authenticates.
D. It allows 802.1x to secure the IP address that port security authenticates.
Answer: A
Q4. What is the maximum number of virtual MAC addresses that GLBP allows per group?
A. 2
B. 4
C. 6
D. 8
Answer: B
Q5. A network engineer wants to add a new switch to an existing switch stack. Which configuration must be added to the new switch before it can be added to the switch stack?
A. No configuration must be added.
B. stack ID
C. IP address
D. VLAN information
E. VTP information
Answer: A
Q6. Which option lists the information that is contained in a Cisco Discovery Protocol advertisement?
A. native VLAN IDs, port-duplex, hardware platform
B. native VLAN IDs, port-duplex, memory errors
C. native VLAN IDs, memory errors, hardware platform
D. port-duplex, hardware platform, memory errors
Answer: A
Q7. Which statement about Cisco Discovery Protocol configuration on a Cisco switch is true?
A. CDP is enabled by default and can be disabled globally with the command no cdp run.
B. CDP is disabled by default and can be enabled globally with the command cdp enable.
C. CDP is enabled by default and can be disabled globally with the command no cdp enable.
D. CDP is disabled by default and can be enabled globally with the command cdp run.
Answer: A
Q8. Which feature must be enabled to eliminate the broadcasting of all unknown traffic to switches that are not participating in the specific VLAN?
A. VTP pruning
B. port-security
C. storm control
D. bpdguard
Answer: A
Q9. Which authentication service is needed to configure 802.1x?
A. RADIUS with EAP Extension
B. TACACS+
C. RADIUS with CoA
D. RADIUS using VSA
Answer: A
Q10. while doing network discovery using Cisco Discovery Protocol, it is found that rapid error tracking is not currently enabled. Which option must be enabled to allow for enhanced reporting mechanisms using Cisco Discovery Protocol?
A. Cisco Discovery Protocol version 2
B. Cisco IOS Embedded Event Manager
C. logging buffered
D. Cisco Discovery Protocol source interface
E. Cisco Discovery Protocol logging options
Answer: A
Q11. The network manager has requested that several new VLANs (VLAN 10, 20, and 30) are allowed to traverse the switch trunk interface. After the command switchport trunk allowed vlan 10,20,30 is issued, all other existing VLANs no longer pass traffic over the trunk. What is the root cause of the problem?
A. The command effectively removed all other working VLANs and replaced them with the new VLANs.
B. VTP pruning removed all unused VLANs.
C. ISL was unable to encapsulate more than the already permitted VLANs across the trunk.
D. Allowing additional VLANs across the trunk introduced a loop in the network.
Answer: A
Q12. Which statement about using EtherChannel on Cisco IOS switches is true?
A. A switch can support up to eight compatibly configured Ethernet interfaces in an EtherChannel. The EtherChannel provides full-duplex bandwidth up to 800 Mbps only for Fast EtherChannel or 8 Gbps only for Gigabit EtherChannel.
B. A switch can support up to 10 compatibly configured Ethernet interfaces in an EtherChannel. The EtherChannel provides full-duplex bandwidth up to 1000 Mbps only for Fast EtherChannel or 8 Gbps only for Gigabit EtherChannel.
C. A switch can support up to eight compatibly configured Ethernet interfaces in an EtherChannel. The EtherChannel provides full-duplex bandwidth up to 800 Mbps only for Fast EtherChannel or 16 Gbps only for Gigabit EtherChannel.
D. A switch can support up to 10 compatibly configured Ethernet interfaces in an EtherChannel. The EtherChannel provides full-duplex bandwidth up to 1000 Mbps only for Fast EtherChannel or 10 Gbps only for Gigabit EtherChannel.
Answer: A
Q13. What is the maximum number of 10 Gigabit Ethernet connections that can be utilized in an EtherChannel for the virtual switch link?
A. 4
B. 6
C. 8
D. 12
Answer: C
Q14. What does the command vlan dot1q tag native accomplish when configured under global
configuration?
A. All frames within the native VLAN are tagged, except when the native VLAN is set to 1.
B. It allows control traffic to pass using the non-default VLAN.
C. It removes the 4-byte dot1q tag from every frame that traverses the trunk interface(s).
D. Control traffic is tagged.
Answer: D
Q15. Which VRRP router is responsible for forwarding packets that are sent to the IP addresses of the virtual router?
A. virtual router master
B. virtual router backup
C. virtual router active
D. virtual router standby
Answer: A
Q16. which feature is automatically enabled when a voice VLAN is configured, but not automatically disabled when a voice VLAN is removed?
A. portfast
B. port-security
C. spanning tree
D. storm control
Answer: A
Q17. In a Cisco switch, what is the default period of time after which a MAC address ages out and is discarded?
A. 100 seconds
B. 180 seconds
C. 300 seconds
D. 600 seconds
Answer: C