Introducing The New!
Surepassexam Collection
Get Unlimited Access to all
Surepassexam's PREMIUM files
Q1. A network engineer is installing a switch for temporary workers to connect to. The engineer does not want this switch participating in Spanning Tree with the rest of the network; however, end user connectivity is still required. Which spanning-tree feature accomplishes this?
A. BPDUblock
B. BPDUfilter
C. BPDUignore
D. BPDUguard
E. BPDUdisable
Answer: B
Q2. An access switch has been configured with an EtherChannel port. After configuring SPAN to monitor this port, the network administrator notices that not all traffic is being replicated to the management server. What is a cause for this issue?
A. VLAN filters are required to ensure traffic mirrors effectively.
B. SPAN encapsulation replication must be enabled to capture EtherChannel destination traffic.
C. The port channel can be used as a SPAN source, but not a destination.
D. RSPAN must be used to capture EtherChannel bidirectional traffic.
Answer: C
Q3. Which option lists the information that is contained in a Cisco Discovery Protocol advertisement?
A. native VLAN IDs, port-duplex, hardware platform
B. native VLAN IDs, port-duplex, memory errors
C. native VLAN IDs, memory errors, hardware platform
D. port-duplex, hardware platform, memory errors
Answer: A
Q4. Refer to the exhibit.
When troubleshooting a network problem, a network analyzer is connected to Port f0/1 of a LAN switch. Which command can prevent BPDU transmission on this port?
A. spanning-tree portfast bpduguard enable
B. spanning-tree bpduguard default
C. spanning-tree portfast bpdufilter default
D. no spanning-tree link-type shared
Answer: C
Q5. Which gateway role is responsible for answering ARP requests for the virtual IP address in GLBP?
A. active virtual forwarder
B. active virtual router
C. active virtual gateway
D. designated router
Answer: C
Q6. Refer to the exhibit.
How many bytes are added to each frame as a result of the configuration?
A. 4-bytes except the native VLAN
B. 8-bytes except the native VLAN
C. 4-bytes including native VLAN
D. 8-bytes including native VLAN
Answer: A
Q7. Which four LACP components are used to determine which hot-standby links become active after an interface failure within an EtherChannel bundle? (Choose four.)
A. LACP system priority
B. LACP port priority
C. interface MAC address
D. system ID
E. port number
F. hot-standby link identification number
G. interface bandwidth
Answer: ABDE
Q8. Which command is needed to enable DHCP snooping if a switchport is connected to a DHCP server?
A. ip dhcp snooping trust
B. ip dhcp snooping
C. ip dhcp trust
D. ip dhcp snooping information
Answer: A
Q9. What is the maximum number of switches that can be stacked using Cisco StackWise?
A. 4
B. 5
C. 8
D. 9
E. 10
F. 13
Answer: D
Q10. After UDLD is implemented, a Network Administrator noticed that one port stops receiving UDLD packets. This port continues to reestablish until after eight failed retries. The port then transitions into the errdisable state. Which option describes what causes the port to go into the errdisable state?
A. Normal UDLD operations that prevent traffic loops.
B. UDLD port is configured in aggressive mode.
C. UDLD is enabled globally.
D. UDLD timers are inconsistent.
Answer: B
Q11. In which portion of the frame is the 802.1q header found?
A. within the Ethernet header
B. within the Ethernet payload
C. within the Ethernet FCS
D. within the Ethernet source MAC address
Answer: A
Q12. Which command configures an HSRP group to become a slave of another HSRP group?
A. standby slave
B. standby group track
C. standby follow
D. standby group backup
Answer: C
Q13. DHCP snooping and IP Source Guard have been configured on a switch that connects to several client workstations. The IP address of one of the workstations does not match any entries found in the DHCP binding database. Which statement describes the outcome of this scenario?
A. Packets from the workstation will be rate limited according to the default values set on the switch.
B. The interface that is connected to the workstation in question will be put into the errdisabled state.
C. Traffic will pass accordingly after the new IP address is populated into the binding database.
D. The packets originating from the workstation are assumed to be spoofed and will be discarded.
Answer: D
Q14. Which statement about Cisco Discovery Protocol configuration on a Cisco switch is true?
A. CDP is enabled by default and can be disabled globally with the command no cdp run.
B. CDP is disabled by default and can be enabled globally with the command cdp enable.
C. CDP is enabled by default and can be disabled globally with the command no cdp enable.
D. CDP is disabled by default and can be enabled globally with the command cdp run.
Answer: A
Q15. Which statement about Cisco devices learning about each other through Cisco Discovery Protocol is true?
A. Each device sends periodic advertisements to multicast address 01:00:0C:CC:CC:CC.
B. Each device broadcasts periodic advertisements to all of its neighbors.
C. Each device sends periodic advertisements to a central device that builds the network topology.
D. Each device sends periodic advertisements to all IP addresses in its ARP table.
Answer: A
Q16. Which two protocols can be automatically negotiated between switches for trunking? (Choose two.)
A. PPP
B. DTP
C. ISL
D. HDLC
E. DLCI
F. DOT1Q
Answer: C,F
Q17. Which feature must be enabled to eliminate the broadcasting of all unknown traffic to switches that are not participating in the specific VLAN?
A. VTP pruning
B. port-security
C. storm control
D. bpdguard
Answer: A