Introducing The New!
Surepassexam Collection
Get Unlimited Access to all
Surepassexam's PREMIUM files
Q1. A network engineer configured an Ethernet switch using these commands. Switchone(config) # Spanning-tree portfast bpdufilter default
Which statement about the spanning-tree portfast feature on the switch is true?
A. If an interface is enabled for portfast receives BDPU, the port goes through the spanning-tree listening, learning, and forwarding states.
B. If an interface is enabled for portfast receives BDPU, the port does not go through the spanning-tree listening, learning, and forwarding states.
C. If an interface is enabled for portfast receives BDPU, the port is shut down immediately.
D. If an interface is enabled for portfast receives BDPU, the port goes into the spanning- tree inconsistent state.
Answer: A
Q2. Which SDM template disables routing and supports the maximum number of unicast MAC addresses?
A. VLAN
B. access
C. default
D. routing
Answer: A
Q3. Which option describes a limitation of LLDP?
A. LLDP cannot provide information about VTP.
B. LLDP does not support TLVs.
C. LLDP can discover only Windows servers.
D. LLDP can discover up to two devices per port.
Answer: A
Q4. Which statement describes what happens when a switch enters dual active recovery mode?
A. The switch shuts down and waits for the VSL link to be restored before sending traffic.
B. All interfaces are shut down in the formerly active virtual switch member, but the new active virtual switch forwards traffic on all links.
C. The switch continues to forward traffic out all links and enables spanning tree on VSL link and all other links to prevent loops.
D. The VSS detects which system was last in active state and shuts down the other switch.
Answer: B
Q5. Which action allows a network engineer to limit a default VLAN from being propagated across all trunks?
A. Upgrade to VTP version 3 for advanced feature set support.
B. Enable VTP pruning on the VTP server.
C. Manually prune default VLAN with switchport trunk allowed vlans remove.
D. Use trunk pruning vlan 1.
Answer: C
Q6. Refer to the exhibit.
Switch A, B, and C are trunked together and have been properly configured for VTP. Switch B has all VLANs, but Switch C is not receiving traffic from certain VLANs. What would cause this issue?
A. A VTP authentication mismatch occurred between Switch A and Switch B.
B. The VTP revision number of Switch B is higher than that of Switch A.
C. VTP pruning is configured globally on all switches and it removed VLANs from the trunk interface that is connected to Switch C.
D. The trunk between Switch A and Switch B is misconfigured.
Answer: C
Q7. For client server failover purposes, the application server team has indicated that they must not have the standard 30 second delay before their switchport enters a forwarding state. For their disaster recovery feature to operate successfully, they require the switchport to enter a forwarding state immediately. Which spanning-tree feature satisfies this requirement?
A. Rapid Spanning-Tree
B. Spanning-Tree Timers
C. Spanning-Tree FastPort
D. Spanning-Tree PortFast
E. Spanning-Tree Fast Forward
Answer: D
Q8. while doing network discovery using Cisco Discovery Protocol, it is found that rapid error tracking is not currently enabled. Which option must be enabled to allow for enhanced reporting mechanisms using Cisco Discovery Protocol?
A. Cisco Discovery Protocol version 2
B. Cisco IOS Embedded Event Manager
C. logging buffered
D. Cisco Discovery Protocol source interface
E. Cisco Discovery Protocol logging options
Answer: A
Q9. Which option is a possible cause for an errdisabled interface?
A. routing loop
B. cable unplugged
C. STP loop guard
D. security violation
Answer: D
Q10. Which statement about using native VLANs to carry untagged frames is true?
A. Cisco Discovery Protocol version 2 carries native VLAN information, but version 1 does not.
B. Cisco Discovery Protocol version 1 carries native VLAN information, but version 2 does not.
C. Cisco Discovery Protocol version 1 and version 2 carry native VLAN information.
D. Cisco Discovery Protocol version 3 carries native VLAN information, but versions 1 and 2 do not.
Answer: A
Q11. Which technique allows specific VLANs to be strictly permitted by the administrator?
A. VTP pruning
B. transparent bridging
C. trunk allowed VLANs
D. VLAN access-list
E. L2P tunneling
Answer: C
Q12. An administrator recently configured all ports for rapid transition using PortFast. After testing, it has been determined that several ports are not transitioning as they should. What is the reason for this?
A. RSTP has been enabled per interface and not globally.
B. The STP root bridge selection is forcing key ports to remain in non-rapid transitioning mode.
C. STP is unable to achieve rapid transition for trunk links.
D. The switch does not have the processing power to ensure rapid transition for all ports.
Answer: C
Q13. In a Cisco switch, what is the default period of time after which a MAC address ages out and is discarded?
A. 100 seconds
B. 180 seconds
C. 300 seconds
D. 600 seconds
Answer: C
Q14. Which option lists the modes that are available for configuring UDLD on a Cisco switch?
A. normal and aggressive
B. active and aggressive
C. normal and active
D. normal and passive
E. normal and standby
Answer: A
Q15. If a network engineer applies the command mac-address-table notification mac-move on a Cisco switch port, when is a syslog message generated?
A. A MAC address or host moves between different switch ports.
B. A new MAC address is added to the content-addressable memory.
C. A new MAC address is removed from the content-addressable memory.
D. More than 64 MAC addresses are added to the content-addressable memory.
Answer: A
Q16. Refer to the exhibit.
What is the result of the SPAN configuration on a Cisco switch?
A. Configure a SPAN session to monitor the received traffic on interface g0/4 only for VLAN 3.
B. Configure a SPAN session to monitor the received traffic on interface g0/4 for all VLANs except VLAN 3.
C. Configure a SPAN session to monitor the received traffic on interface g0/5 only for VLAN 3.
D. Configure a SPAN session to monitor the received traffic on interface g0/5 for all VLANs except VLAN 3.
Answer: A
Q17. What is the size of the VLAN field inside an 802.1q frame?
A. 8-bit
B. 12-bit
C. 16-bit
D. 32-bit
Answer: B