Introducing The New!
Surepassexam Collection
Get Unlimited Access to all
Surepassexam's PREMIUM files
Q1. refer to the exhibit.
f1/0 and f1/1 have the same end-to-end path cost to the designated bridge. Which action is needed to modify the Layer 2 spanning-tree network so that traffic for PC1 VLAN from switch SW3 uses switchport f1/1 as a primary port?
A. Modify the spanning-tree port-priority on SW1 f1/1 to 0 and f1/0 to 16.
B. Modify the spanning-tree port-priority on SW1 f1/1 to 16 and f1/0 to 0.
C. Modify the spanning-tree port-priority on SW2 f1/1 to 0 and f1/0 to 16.
D. Modify the spanning-tree port-priority on SW2 f1/1 to 16 and f1/0 to 0.
Answer: C
Q2. An EtherChannel bundle has been established between a Cisco switch and a corporate web server. The network administrator noticed that only one of the EtherChannel links is being utilized to reach the web server. What should be done on the Cisco switch to allow for better EtherChannel utilization to the corporate web server?
A. Enable Cisco Express Forwarding to allow for more effective traffic sharing over the EtherChannel bundle.
B. Adjust the EtherChannel load-balancing method based on destination IP addresses.
C. Disable spanning tree on all interfaces that are participating in the EtherChannel bundle.
D. Use link-state tracking to allow for improved load balancing of traffic upon link failure to the server.
E. Adjust the EtherChannel load-balancing method based on source IP addresses.
Answer: E
Q3. A network engineer is trying to deploy a PC on a network. The engineer observes that when the PC is connected to the network, it takes 30 to 60 seconds for the PC to see any activity on the network interface card. Which Layer 2 enhancement can be used to eliminate this delay?
A. Configure port duplex and speed to auto negotiation.
B. Configure port to duplex full and speed 1000.
C. Configure spanning-tree portfast.
D. Configure no switchport.
Answer: C
Q4. Which command configures an HSRP group to become a slave of another HSRP group?
A. standby slave
B. standby group track
C. standby follow
D. standby group backup
Answer: C
Q5. after configuring new data VLANs 1020 through 1030 on the VTP server, a network engineer notices that none of the VTP clients are receiving the updates. What is the problem?
A. The VTP server must be reloaded.
B. The VTP version number must be set to version 3.
C. After each update to the VTP server, it takes up to 4 hours propagate.
D. VTP must be stopped and restarted on the server.
E. Another switch in the domain has a higher revision number than the server.
Answer: B
Q6. Which SDM template disables routing and supports the maximum number of unicast MAC addresses?
A. VLAN
B. access
C. default
D. routing
Answer: A
Q7. For security reasons, the IT manager has prohibited users from dynamically establishing trunks with their associated upstream switch. Which two actions can prevent interface trunking? (Choose two.)
A. Configure trunk and access interfaces manually.
B. Disable DTP on a per interface basis.
C. Apply BPDU guard and BPDU filter.
D. Enable switchport block on access ports.
Answer: A,B
Q8. A manager tells the network engineer to permit only certain VLANs across a specific trunk interface. Which option can be configured to accomplish this?
A. allowed VLAN list
B. VTP pruning
C. VACL
D. L2P tunneling
Answer: A
Q9. Refer to the exhibit.
The users in an engineering department that connect to the same access switch cannot access the network. The network engineer found that the engineering VLAN is missing from the database. Which action resolves this problem?
A. Disable VTP pruning and disable 802.1q.
B. Update the VTP revision number.
C. Change VTP mode to server and enable 802.1q.
D. Enable VTP pruning and disable 802.1q.
Answer: C
Q10. Refer to the exhibit.
What is the result of the configuration?
A. The EtherChannels would not form because the load-balancing method must match on the devices.
B. The EtherChannels would form and function properly even though the load-balancing and EtherChannel modes do not match.
C. The EtherChannels would form, but network loops would occur because the load- balancing methods do not match.
D. The EtherChannels would form and both devices would use the dst-ip load-balancing method because Switch1 is configured with EtherChannel mode active.
Answer: B
Q11. Which statement describes what happens if all VSL connections between the virtual switch
members are lost?
A. Both virtual switch members cease to forward traffic.
B. The VSS transitions to the dual active recovery mode, and both virtual switch members continue to forward traffic independently.
C. The virtual switch members reload.
D. The VSS transitions to the dual active recovery mode, and only the new active virtual switch continues to forward traffic.
Answer: D
Q12. RSPAN has been configured on a Cisco Catalyst switch; however, traffic is not being replicated to the remote switch. Which type of misconfiguration is a cause?
A. The RSPAN designated VLAN is missing the remote span command.
B. The local and remote RSPAN switches are configured using different session IDs.
C. The local RSPAN switch is replicating only Rx traffic to the remote switch.
D. The local switch is overloaded with the amount of sourced traffic that must be replicated to the remote switch.
Answer: A
Q13. Which SDM template is the most appropriate for a Layer 2 switch that provides connectivity to a large number of clients?
A. VLAN
B. default
C. access
D. routing
Answer: A
Q14. The network manager has requested that several new VLANs (VLAN 10, 20, and 30) are allowed to traverse the switch trunk interface. After the command switchport trunk allowed vlan 10,20,30 is issued, all other existing VLANs no longer pass traffic over the trunk. What is the root cause of the problem?
A. The command effectively removed all other working VLANs and replaced them with the new VLANs.
B. VTP pruning removed all unused VLANs.
C. ISL was unable to encapsulate more than the already permitted VLANs across the trunk.
D. Allowing additional VLANs across the trunk introduced a loop in the network.
Answer: A
Q15. Refer to the exhibit.
When troubleshooting a network problem, a network analyzer is connected to Port f0/1 of a LAN switch. Which command can prevent BPDU transmission on this port?
A. spanning-tree portfast bpduguard enable
B. spanning-tree bpduguard default
C. spanning-tree portfast bpdufilter default
D. no spanning-tree link-type shared
Answer: C
Q16. After an EtherChannel is configured between two Cisco switches, interface port channel 1 is in the down/down state. Switch A is configured with channel-group 1 mode active, while Switch B is configured with channel-group 1 mode desirable. Why is the EtherChannel bundle not working?
A. The switches are using mismatched EtherChannel negotiation modes.
B. The switch ports are not configured in trunking mode.
C. LACP priority must be configured on both switches.
D. The channel group identifier must be different for Switch A and Switch B.
Answer: A
Q17. After implementing VTP, the extended VLANs are not being propagated to other VTP switches. What should be configured for extended VLANs?
A. VTP does not support extended VLANs and should be manually added to all switches.
B. Enable VTP version 3, which supports extended VLAN propagation.
C. VTP authentication is required when using extended VLANs because of their ability to cause network instability.
D. Ensure that all switches run the same Cisco IOS version. Extended VLANs will not propagate to different IOS versions when extended VLANs are in use.
Answer: B