Introducing The New!
Surepassexam Collection
Get Unlimited Access to all
Surepassexam's PREMIUM files
P.S. High quality 300-135 torrent are available on Google Drive, GET MORE: https://drive.google.com/open?id=1b8IflMM01Yv-CELfeZXF0P5UV8NaZBSU
Q7. Given the multicast IP address of 224.193.5.10, what would the corresponding multicast MAC address be?
A. 00-00-0c-c0-05-0a
B. 00-00-0c-cl-05-0a
C. 01-00-5e-00-00-0c
D. 01-00-5e-41-05-0a
E. 00-00-0c-01-00-5e
F. 01-00-5e-cl-05-0a
Answer: F
Explanation:
First three octets are 01-00-05e for every single multicast address.Las three octets are the hexadecimal version of the las three octets of the IP address, in this case 193.5.10 is translated to c1-05-0a.
Q8. The implementations group has been using the test bed to do a u2021proof-of-conceptu2021 that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to isolate the cause of this fault and answer the following question.
What is the solution to the fault condition?
A. Under the global configuration, delete the no ip dhcp use vrf connected command.
B. Under the IP DHCP pool configuration, delete the default -router 10.2.1.254 command
and enter the default-router 10.1.4.5 command.
C. Under the IP DHCP pool configuration, delete the network 10.2.1.0 255.255.255.0 command and enter the network 10.1.4.0 255.255.255.0 command.
D. Under the IP DHCP pool configuration, issue the no ip dhcp excluded-address 10.2.1.1 10.2.1.253 command and enter the ip dhcp excluded-address 10.2.1.1 10.2.1.2 command.
Answer: D
Explanation:
On R4 the DHCP IP address is not allowed for network 10.2.1.0/24 which clearly shows the problem lies on R4 & the problem is with DHCP
Q9. Which of the following commands will display a router's crypto map IPsec security association settings?
A. show crypto map ipsec sa
B. show crypto map
C. show crypto engine connections active
D. show ipsec crypto map
E. show crypto map sa
F. show ipsec crypto map sa
Answer: A
Q10. The implementations group has been using the test bed to do a u2021proof-of-conceptu2021 that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to isolated the cause of this fault and answer the following questions.
What is the solution to the fault condition?
A. R1
B. R2
C. R3
D. R4
E. DSW1
F. DSW2
G. ASW1
H. ASW2
Answer: G
Explanation:
The problem here is that VLAN 10 is not configured on the proper interfaces on switch ASW1.
Q11. The implementations group has been using the test bed to do a u2021proof-of-conceptu2021 that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services,
NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to isolated the cause of this fault and answer the following questions.
The fault condition is related to which technology?
A. NTP
B. IP DHCP Helper
C. IPv4 EIGRP Routing
D. IPv6 RIP Routing
E. IPv4 layer 3 security
F. Switch-to-Switch Connectivity
G. Loop Prevention
H. Access Vlans
I. Port Security
J. VLAN ACL / Port ACL
K. Switch Virtual Interface
Answer: J
Explanation:
On DSW1, VALN ACL, Need to delete the VLAN access-map test1 whose action is to drop access-list 10; specifically 10.2.1.3
Q12. The following commands are issued on a Cisco Router:
Router(configuration)#access-list 199 permit tcp host 10.1.1.1 host 172.16.1.1
Router(configuration)#access-list 199 permit tcp host 172.16.1.1 host 10.1.1.1 Router(configuration)#exit
Router#debug ip packet 199
What will the debug output on the console show?
A. All IP packets passing through the router
B. Only IP packets with the source address of 10.1.1.1
C. All IP packets from 10.1.1.1 to 172.16.1.1
D. All IP Packets between 10.1.1.1 and 172.16.1.1
Answer: D
Explanation:
In this example, the u201cdebug ip packetu201d command is tied to access list 199, specifying which IP packets should be debugged. Access list 199 contains two lines, one going from the host with IP address 10.1.1.1 to 172.16.1.1 and the other specifying all TCP packets from host 172.16.1.1 to 10.1.1.1.
Q13. The implementations group has been using the test bed to do a u2021proof-of-conceptu2021 that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to isolated the cause of this fault and answer the following questions.
On which device is the fault condition located?
A. R1
B. R2
C. R3
D. R4
E. DSW1
F. DSW2
G. ASW1
Answer: A
Explanation:
The BGP neighbor statement is wrong on R1.
Topic 10, Ticket 5 : NAT ACL
Topology Overview (Actual Troubleshooting lab design is for below network design)
u2711 Client Should have IP 10.2.1.3
u2711 EIGRP 100 is running between switch DSW1 & DSW2
u2711 OSPF (Process ID 1) is running between R1, R2, R3, R4
u2711 Network of OSPF is redistributed in EIGRP
u2711 BGP 65001 is configured on R1 with Webserver cloud AS 65002
u2711 HSRP is running between DSW1 & DSW2 Switches
The company has created the test bed shown in the layer 2 and layer 3 topology exhibits. This network consists of four routers, two layer 3 switches and two layer 2 switches.
In the IPv4 layer 3 topology, R1, R2, R3, and R4 are running OSPF with an OSPF process number 1.
DSW1, DSW2 and R4 are running EIGRP with an AS of 10. Redistribution is enabled where necessary.
R1 is running a BGP AS with a number of 65001. This AS has an eBGP connection to AS 65002 in the ISPu2021s network. Because the companyu2021s address space is in the private range. R1 is also providing NAT translations between the inside (10.1.0.0/16 & 10.2.0.0/16) networks and outside (209.65.0.0/24) network.
ASW1 and ASW2 are layer 2 switches.
NTP is enabled on all devices with 209.65.200.226 serving as the master clock source. The client workstations receive their IP address and default gateway via R4u2021s DHCP server.
The default gateway address of 10.2.1.254 is the IP address of HSRP group 10 which is running on DSW1 and DSW2.
In the IPv6 layer 3 topology R1, R2, and R3 are running OSPFv3 with an OSPF process number 6.
DSW1, DSW2 and R4 are running RIPng process name RIP_ZONE.
The two IPv6 routing domains, OSPF 6 and RIPng are connected via GRE tunnel running over the underlying IPv4 OSPF domain. Redistrution is enabled where necessary.
Recently the implementation group has been using the test bed to do a u2021proof-of-conceptu2021 on several implementations. This involved changing the configuration on one or more of the devices. You will be presented with a series of trouble tickets related to issues introduced during these configurations.
Note: Although trouble tickets have many similar fault indications, each ticket has its own issue and solution.
Each ticket has 3 sub questions that need to be answered & topology remains same. Question-1 Fault is found on which device,
Question-2 Fault condition is related to,
Question-3 What exact problem is seen & what needs to be done for solution
Client is unable to ping IP 209.65.200.241
Solution
Steps need to follow as below:-
u2711 When we check on client 1 & Client 2 desktop we are not receiving DHCP address
from R4
Ipconfig ----- Client will be receiving IP address 10.2.1.3
u2711 IP 10.2.1.3 will be able to ping from R4 , R3, R2, R1
u2711 Look for BGP Neighbourship
Sh ip bgp summary ----- State of BGP will be in established state & will be able to receive I prefix (209.65.200.241)
u2711 As per troubleshooting we are able to ping ip 10.2.1.3 from R1 & BGP is also receiving prefix of webserver & we are able to ping the same from R1. Further troubleshooting needs to be done on R1 on serial 0/0/1
u2711 Check for running config. i.e sh run for interface serial 0/0/1..
!
!
From above snapshot we are able to see that IP needs to be PAT to serial 0/0/1 to reach web server IP
(209.65.200.241). But in access-list of NAT IP allowed IP is 10.1.0.0/16 is allowed & need
10.2.0.0 /16 to
u2711 As per troubleshooting we are able to ping ip 10.2.1.3 from R1 & BGP is also receiving prefix of web server & we are able to ping the same from R1. Its should be checked further for running config of interface for stopping
u2711 Change required: On R1 we need to add the client IP address for reachability to server to the access list that is used to specify which hosts get NATed.
Q14. Which of the following statements are true concerning the command ip sla monitor responder type tcpconnect ipaddress 10.1.1.1 port 23? (Choose all that apply.)
A. The command will initiate a probe with a destination IP address of 10.1.1.1.
B. The command is used on the IP SLA responder and the IP SLA source.
C. The command will allow only source address 10.1.1.1 to source probes.
D. The command will initiate a probe with a destination Telnet port.
E. The command is used to make the router a responder.
F. The command will initiate a probe with a source port of 23.
Answer: A,D
Q15. The implementations group has been using the test bed to do a u2021proof-of-conceptu2021 that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241.
After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to isolated the cause of this fault and answer the following questions.
Which is the solution to the fault condition?
A. Under the EIGRP process, delete the redistribute ospf 1 route-map OSPF_ to_ EIGRP command and enter the redistribute ospf 1 route-map OSPF - > EIGRP command.
B. Under the EIGRP process, delete the redistribute ospf 1 route-map OSPF_ to_ EIGRP command and enter the redistribute ospf 6 metric route-map OSPF - > EIGRP command.
C. Under the OSPF process, delete the redistribute eigrp10 subnets route-map EIGPR -
>OSPF command and enter the redistribute eigrp10 subnets route-map OSPF - > EIGRP command.
D. Under the OSPF process, delete the redistribute eigrp10 subnets route-map EIGPR -
>OSPF command and enter the redistribute eigrp10 subnets route-map EIGPR - > OSPF command.
E. Under the EIGRP process, delete the redistribute ospf 1 route-map OSPF _to_ EIGRP command and enter redistribute ospf 1 metric 100000 100 100 1 15000 route_ map OSPF
_to _EIGRP command
Answer: A
Explanation:
On R4, in the redistribution of EIGRP routing protocol, we need to change name of route- map to resolve the issue. It references route-map OSPF_to_EIGRP but the actual route map is called OSPF->EIGRP.
Q16. Which of the following are correct statements?
A. EIGRP advertises the best routes to its neighbor.
B. EIGRP uses "cost" to determine best path.
C. EIGRP allows unequal cost load balancing.
D. OSPF requires neighbor adjacencies before updates are sent.
E. EIGRP advertises all routes to its neighbor.
F. OSPF allows unequal cost load balancing.
Answer: A,C,D
P.S. Easily pass 300-135 Exam with Examcollection High quality Dumps & pdf vce, Try Free: http://www.examcollectionuk.com/300-135-vce-download.html (146 New Questions)