Cisco 300-165 Free Practice Questions

NEW QUESTION 1
What is the status of FCoE license on Cisco Nexus 5548 switch?

• A. FCoE license is not installed
• B. FCoE license is installed, but it is expired
• C. FCoE license is installed and status is enabled
• D. FCoE license does not need to be installed because it is part of ENTERPRISE_PKG

Answer: C

NEW QUESTION 2
Refer to the exhibit.

You are implementing a rollback of the configuration to a checkpoint. Which result of running the command is true?

• A. It stops a rollback if an error occurs.
• B. It creates a rollback only if no errors occur.
• C. It creates a rollback in a stable state.
• D. It creates a rollback but skips any error

Answer: D

NEW QUESTION 3
When configure HSPR on IPv6 enabled interface, which two configuration is correct.

• A. switchA{config-if)» standbyt 6 preempt
• B. switchA(config-if)» hsrp <group-number>
• C. switchA(config-if)ff key 6
• D. switchA{config-if)» hsrp version 2
• E. switchA{config-if)B priority <level>

Answer: B

NEW QUESTION 4
DRAG DROP
Drag and drop the RP mechanisms on the left to their correct redundancy implementations on the right.

Answer:

Explanation:

NEW QUESTION 5
What is the status of FC interface associated with ethernet 1/5 indicate?

• A. Trunk VSAN 11 is isolated
• B. Inteface vfc 5 is up and running for the assigned VSAN
• C. Trunk VSAN 11 is intializing
• D. VSAN to FC mapping is not working as expected

Answer: B

NEW QUESTION 6
DRAG DROP
Drag the description on the left to the most appropriate FCoE protocol or feature on the right.

Answer:

Explanation: ENODES: During FLOGI or FDISC, the ENode advertises the addressing modes it supports. If the FC switch supports an addressing mode that the ENode uses, the virtual link can be established, and the devices can communicate.
FIP: FIP is the set of control plane functions that enable discovery of FCoE-capable devices across FCoE passthrough switches and establishment of legal combinations of virtual links.
FCF: FCoE Initialization Protocol (FIP) is the FCoE control protocol responsible for establishing and maintaining Fibre Channel virtual links between pairs of FCoE devices (ENodes or FCFs). During the virtual link establishment phase, FIP first discovers FCoE VLANs and remote virtual FC interfaces; then it performs virtual link initialization functions (fabric login [FLOGI] and fabric discovery [FDISC], or exchange link parameters [ELP]) similar to their native Fibre Channel equivalents. After the virtual link is established, Fibre Channel payloads can be exchanged on the virtual link, and FIP remains in
the background to perform virtual link maintenance functions; it continuously verifies reachability between the two virtual FC interfaces on the Ethernet network, and it offers primitives to delete the virtual link in response to administrative actions to that effect. This document does not describe the virtual link maintenance functions of FIP.

NEW QUESTION 7
FabricPath switch-id is 25 and load-balance is configured for L3/L4 and rotate amount is 14 byte. What information is true about FabricPath switch-id?

• A. FabricPath topology requires manual configuration of switch-id which has a range from 1 to 4095
• B. Every FabricPath must have a manually configured switch-id for it to form a FabricPath topology
• C. FabricPath topology requires manual configuration of switch-id which has a range from 1 to 4099
• D. You do not have to manually assign a switch ID unless you are running a virtual port channel plus (vPC+) because the system assigns a switch ID for you when you enable FabricPath

Answer: D

Explanation: fabricpath switch-id (vPC)
To configure a virtual port channel plus (vPC+) switch ID, use the fabricpath switch-id command. To remove the FabricPath switch from a vPC domain, use the no form of this command.
fabricpath switch-id switch-id
no fabricpath switch-id [ switch-id ] Usage Guidelines
You do not have to manually assign a switch ID (unless you are running a vPC+); the system assigns a switch ID for you when you enable FabricPath.
Note You must assign the same vPC+ switch ID to each of the two vPC+ peer devices before they can form an adjacency.
This command requires an Enhanced Layer 2 license. Examples
This example shows how to configure a vPC+ switch ID on a FabricPath-enabled device: switch# configure terminal
switch(config)# vpc domain 1
switch(config-vpc-domain)# fabricpath switch-id 1
Configuring fabricpath switch id will flap vPCs. Continue (yes/no)? [no]

NEW QUESTION 8
What is the purpose of the resequence command for ACLs?

• A. to rearrange the order of the access lists in the running configuration
• B. to assign new sequence numbers to the rules in an ACL
• C. to refresh ACI programming in ASICs to apply the ACL changes
• D. to rearrange ACL entries

Answer: B

Explanation: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/4_1/nxos/security/configuration/guide/sec_nx-os-cfg/sec_macacls.pdf

NEW QUESTION 9
You have multiple OTV edge devices in each OTV site. Which configuration prevents an end-to-end STP loop?

• A. selective unicast flooding
• B. AED election
• C. FHRP filtering
• D. ARP local caching

Answer: B

NEW QUESTION 10
Which option shows how to configure an ERSPAN Type III source session in Cisco NX-OS 6.2?
A)

B)

C)

D)

• A. Option A
• B. Option B
• C. Option C
• D. Option D

Answer: C

NEW QUESTION 11
Which statement about RBAC user roles on a Cisco Nexus switch is true?

• A. If you belong to multiple roles, you can execute only the commands that are permitted by bothroles (logical AND).
• B. Access to a command takes priority over being denied access to a command.
• C. The predefined roles can only be changed by the network administrator (superuser).
• D. The default SAN administrator role restricts configuration to Fibre Channel interfaces.
• E. On a Cisco Nexus 7000 Series Switch, roles are shared between VDC

Answer: B

Explanation: If you belong to multiple roles, you can execute a combination of all the commands permitted by these roles. Access to a command takes priority over being denied access to a command. For example, suppose a user has RoleA, which denied access to the configuration commands. However, the users also have RoleB, which has access to the configuration commands. In this case, the users have access to the configuration commands.
Reference: http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/configuration/guide/cli/ CLIConfigurationGuide/sec_rbac.html

NEW QUESTION 12
Which two options are limitations of NetFlow Version 5? (Choose two.)

• A. no support for IPv6, Layer 2, or MPLS fields
• B. fixed field specifications
• C. excessive network utilization
• D. analyzes all packets on the interface

Answer: AB

NEW QUESTION 13
DRAG DROP
Refer to the exhibit.

System A must be able to use VXLAN peer discovery to send a message to System B to receive a response. Drag and drop the peer discovery steps from the left into the correct order on the right.

Answer:

Explanation:

NEW QUESTION 14
Which option accurately describes the implementation of Fibre Channel domain IDs?

• A. Are assigned on a peer-switch basis
• B. Are assigned on a per-line card basis
• C. Must be the dame on all on the Fabre Channel switch in the fabric
• D. Must be unique on all the Fibre Channel switches in the fabric

Answer: A

NEW QUESTION 15
You plan to implement the OSPF protocol whithin the data center network. Which two statements accurately describe OSPF on the Cisco NX-OS platform? (Choose two.)

• A. The default reference bandwidth is 10 Gbps.
• B. OSPF does nor require additional licenses.
• C. The OSPF area can be configured by using decimal notation only.
• D. Redistributing routes into OSPF requires a route map.
• E. The secondary IP address is advertised by defaul

Answer: DE

NEW QUESTION 16
Which two issues explain why a packet is not being routed as desired in a policy-based routing configuration? (Choose two.)

• A. The next hop that is configured in the route map has a higher metric than the default next hop.
• B. The route map is not applied to the egress interface.
• C. The next hop that is configured in the route map is not in the global routing table.
• D. The route map is not applied to the ingress interface.
• E. The next hop that is configured in the route map has a lower metric than the default next ho

Answer: CE

Explanation: The next hop that is configured in the route map is not in the global routing table then the packet will not be forwarded as desired. The next hop that is configured in the route map has a higher metric than the default next hop.