Cisco 300-370 Free Practice Questions

NEW QUESTION 1
An engineer uses the shutdown and no shutdown commands on a switch port that an access point is connected to because the AP had disassociated. These commands usually resolve the issue.
Which troubleshooting methodology does this demonstrate?

• A. bottom-up


• B. top-down


• C. divide and conquer


• D. shoot from the hip

Answer: D

NEW QUESTION 2
Which three options are characteristics of a rogue AP that poses a high-security risk? (Choose three.)

• A. a high RSSI


• B. accepts clients


• C. a foreign SSID


• D. a distant location


• E. open authentication


• F. a low RSSI

Answer: BEF

NEW QUESTION 3
An engineer is concerned about rogue-on-wire and wants to enable port security. Which guideline must the engineer follow?

• A. Configure Switched Port Analyzer destination ports as secure.


• B. Use 802 1x with port security to prevent MAC spoofing.


• C. Enable port security on dynamic access ports.


• D. Employ static MAC address configuration for APs with port securit

Answer: A

NEW QUESTION 4
A WLAN was installed at a high AP density. DTPC is lowering the transmit power of many APs too low. Which change m the DTPC transmit power threshold must be made to allow APs to globally increase
AP transmit power by 3dBm?

• A. from 70 dBm to 73 dBm


• B. from -70 dBm to -73 dBm


• C. from 70 dBm to 67 dBm


• D. from -70 dBm to -67 dBm

Answer: D

NEW QUESTION 5
A mobile workstation in a factory contains an AP that is configured as a workgroup bridge. When the workstation moves, it loses connectivity and disrupts operation. What can the engineer implement
to minimize roaming problems?

• A. Use 802.1X authentication.


• B. Use Cisco Centralized Key Management for fast roaming.


• C. Use AES for encryption.


• D. Use the mobile station comman

Answer: B

NEW QUESTION 6
Wireless users encounter choppy VoVLAN on one floor of a building. Which troubleshooting approach will determine the cause of the issue in the least amount of time?

• A. move the problem


• B. top down


• C. shoot from the hip


• D. bottom up

Answer: A

NEW QUESTION 7
You are debugging a WGB client. Which description of the client is true?

• A. disconnected from the wired device


• B. triggered to reauthenticate


• C. disconnected from the authentication server


• D. triggered to roam

Answer: D

NEW QUESTION 8
Refer to the exhibit.

Which statement describes how the Band Select feature works on the wireless controller?

• A. The access point uses the load balancing feature to move the clients to 5 Ghz.


• B. The access point changes the DTIM period on the 2 4 Ghz band.


• C. The access point recommends the band in the association response to the client.


• D. The access point ignores and delays the probe request of the client on the 2 4 Gh

Answer: C

NEW QUESTION 9
An engineer is creating a custom rogue classification rule directly on a controller. Which two conditions are possible when adding a custom rule to a controller? (Choose two.)

• A. internal


• B. ad hoc


• C. client-count


• D. duration


• E. WLAN


• F. open authentication

Answer: AD

NEW QUESTION 10
Which three options can be configured as roaming triggers on a WGB? (Choose three.)

• A. SNR


• B. co-channel interference


• C. RSSI


• D. packet fragmentation


• E. packet retries


• F. minimum data rate

Answer: CEF

NEW QUESTION 11
An engineer is troubleshooting AP join issues on a wireless infrastructure. While gathering debugs, the engineer notices that one of the commands may generate an excessive an excessive amount of data on the console. Which command causes this to occur?

• A. debug capwap detail enable


• B. debug capwap errors enable


• C. debug capwap info enable


• D. debug capwap events enable


• E. debug capwap packet enable


• F. debug capwap payload enable

Answer: B

NEW QUESTION 12
Clients are maintaining association to access points that they were previously connected to rather than
roaming to adjacent access points with higher received signal strength. Which two actions can be taken to fix this issue? (Choose two.)

• A. Set DCA channel sensitivity to low.


• B. Utilize Rx-SOP.


• C. Increase access point power.


• D. Enable optimized roaming.


• E. Add access points to the are

Answer: AD

NEW QUESTION 13
Two 5508 Wireless Lan Controllers are managing all Access Points throughout the network The WLCs are located in different locations to provide geographical redundancy A Mobility Group has been configured on both WLCs and has a UP status on both Controllers The APs m location A are statically configured to use Controller A as the Primary and Controller B as the Secondary If the WLC in location A goes offline, the APs successfully join the WLC m location B but they do not failover to their Primary configured Controller What configuration task will fix this issue'

• A. Change the AP Failover Priority to critical.


• B. Enable AP Fallback globally on the WLC.


• C. Configure the WLC in location A as Primary using the CAPWAP AP Controller IP Address commandon all the location A Access Points.


• D. Use DHCP Option 43 and specify WLC in location A as Primar

Answer: C

NEW QUESTION 14
Which channel width is the maximum that can be obtained by bonding two 802.11 ac subchannels according to US regulations?

• A. 160 MHz


• B. 120 MHz


• C. 84 MHz


• D. 240 MHz

Answer: A

Explanation:
To increase throughput, 802.11ac introduces two new channel widths. All 802.11ac devices are required to support 80 MHz channels, which doubles the size of the spectral channel over 802.11n. It further adds a 160 MHz channel option for even higher speeds. Due to the limitations of finding contiguous 160 MHz spectrum, the standard allows for a 160 MHz channel to be either a single contiguous block or two noncontiguous 80 MHz channels.

NEW QUESTION 15
After you perform a post-installation RF survey for a customer with ID 339696181, you discover that all areas have at least -67 dBm RSSI, 25 dB SNR, and 10 percent cell overlap. The customer, however, reports one-way audio issues on VoWLAN phones.
Which option is a possible cause of the issue?

• A. The cell overlap is too low.


• B. There are coverage black spots.


• C. Non Wi-Fi interference causes a high noise floor.


• D. The RSSI is too hig

Answer: D

NEW QUESTION 16
When implementing interface groups, how are the IP addresses sourced via DHCP for wireless clients?

• A. through the primary interface of the group


• B. through round robin between interfaces


• C. through interface group definition


• D. through the interface receiving the first response

Answer: B

NEW QUESTION 17
Which three details are contained within the LWAPP discovery response sent by each WLC to enable the LAP to choose a WLC? (Choose three.)

• A. the controller sysName


• B. an AP-manager IP address


• C. the WLC IOS version


• D. the mobility domain name


• E. the master controller flag


• F. the DNS server address

Answer: ABE

NEW QUESTION 18
A recently acquired Cisco Aironet 1550 series AP is unable to join the WLC. This message is observed on the AP console:
AAA Authentication Failure for UserName:CC93.1981.0035 User Type: WLAN USER Which action must be taken for the AP to associate with the controller?

• A. Add MAC address CC93.1981.0035 to the Security AAA AP policy Authorization List.


• B. Authenticate the AP to the WLC from the console using an admin account on the WLC.


• C. Add MAC address CC93.1981.035 to the Security AAA MAC Filtering tab.


• D. Import the self-signed certificate of the AP to the Security:Certificate:LSC tab.


• E. Import the self-signed certificate of the AP to the Security:Certificate:SSC ta

Answer: A

NEW QUESTION 19
An engineer has configured 802 1x for the network and all but one of the APs are passing authentication. Which configuration is causing the failure?

• A. The AP has override global credentials checked.


• B. The switch AAA credentials do not match what is configured on ISE.


• C. The controller 802 1x supplicant credentials do not match what is configured on ISE


• D. EAP-FAST is configured on ISE for this A

Answer: A

NEW QUESTION 20
DRAG DROP
Drag and drop the Layer 3 WLAN controller mutual authentication join process events on the left into the order in which they occur on the right Not all options are used.

• A. Mastered


• B. Not Mastered

Answer: A

Explanation:

NEW QUESTION 21
......