Cisco 300-615 Free Practice Questions

NEW QUESTION 1

Refer to the exhibit. An engineer is investigating a role mapping issue on a switch. The users report that they cannot view the IP addresses under the tenant “corp”. Which action resolves the issue?

• A. Add the users to the RADIUS server.
• B. Update the UNIX ID.
• C. Configure the correct secret password between the APIC and the RADIUS server.
• D. Add the updated avpair to include/corp/admin/

Answer: C

NEW QUESTION 2
A request to activate the port security database is rejected. Which action do you perform to investigate the cause of the issue?

• A. Enable the auto-learning feature.
• B. Use the force option to identify rejected devices.
• C. Find conflicting entries between the active and configuration databases.
• D. Verify that devices are fully attached to the active database.

Answer: B

NEW QUESTION 3
A network administrator attempts to install an application in the Cisco NX-OS Guest shell and receives an error that there is not enough space on the disk. Which command must the administrator run to increase the disk space available in the Guest shell?

• A. guestshell growdisk rootfs [size-in-MB]
• B. guestshell pvextend rootfs [size-in-MB]
• C. guestshell resize rootfs [size-in-MB]
• D. guestshell resize2fs rootfs [size-in-MB]

Answer: C

NEW QUESTION 4

Refer to the exhibit. An engineer is configuring boot from iSCSI on a Cisco UCS B-Series Blade Server, but the LUN fails to mount. Which action resolves the issue?

• A. Statically configure the target information in the Boot Policy.
• B. Configure an MTU size of 9000 on the appliance port.
• C. Configure a QoS policy on the vNIC.
• D. Set a connection timeout value of 250 in the iSCSI Adapter Policy.

Answer: A

NEW QUESTION 5
An upgrade of protected RPMs from the Bash shell did not take effect. Which action is required for the changes to take effect?

• A. Restart the Bash shell.
• B. Reload the switch.
• C. Upgrade the RPMs from the Guest shell.
• D. Disable and reenable the Bash feature.

Answer: D

NEW QUESTION 6

Refer to the exhibit. After the configuration is performed, guestshell continues to use 2%CPU. Which action resolves the issue?

• A. Resync the database
• B. Recreate the guestshell
• C. Reboot the guestshell
• D. Reboot the switch

Answer: C

NEW QUESTION 7
An engineer must replace a failed memory on a Cisco UCS B-Series Blade Server. After the replacement was done, the server has a “resolve slot” warning. Which server maintenance action resolves the issue?

• A. Perform diagnostic interrupt on the server.
• B. Re-acknowlegement the server.
• C. Reset the server.
• D. Decomission the server.

Answer: B

NEW QUESTION 8
An engineer is implementing a storage VDC, but fails. Which two prerequisites must be in place before a storage VDC is implemented? (Choose two.)

• A. M-Series module
• B. ESSENTIALS license
• C. STORAGE-ENT license
• D. FCoE license
• E. F-Series module

Answer: DE

NEW QUESTION 9

Refer to the exhibit. Partial configuration from N9K-1 and N9K-2 is included. The client has two WANs connected. WAN-1 is for normal business-day activities.
WAN-2 is for server backups during nonworking hours of 1:00 a.m. to 5:00 a.m. daily.
The client says that at the scheduled time for backup, the data center server failed to use the WAN-2 link to back up the servers to the cloud backup system. What is the solution to this problem?

• A. The event timer must be written in epoch time format.
• B. The Cisco Nexus switch must be configured with one applet because a configuration with two applets will fail.
• C. The Cron entry must be configured without double quotes.
• D. The applet called “Backup” must include an action to remove the current static route.

Answer: D

NEW QUESTION 10
DRAG DROP
Drag and drop the actions from the left onto the faults that they resolve on the right. Not all options are used.
Select and Place:

• A. Mastered
• B. Not Mastered

Answer: A

Explanation:

NEW QUESTION 11

Refer to the exhibit. A web browser displays a “not secure” warning message when accessing the web interface of Cisco UCS Manager. Which action resolves the issue?

• A. Load third-party certificate to UCS Manager.
• B. Use the correct TCP port for HTTPS.
• C. Use a supported web browser.
• D. Use a supported version of UCS Manager.

Answer: A

NEW QUESTION 12
An attempt to use a global vNIC redundancy template pair results in a service profile that fails to apply. Which action resolves the issues?

• A. Create the peer names before creating the templates.
• B. Assign the secondary template first, and then set the peer name.
• C. Assign both templates simultaneously.
• D. Assign the primary template first, and then set the peer name.

Answer: D

NEW QUESTION 13
Refer to the exhibit. A new Cisco Nexus 5548 Switch connects to a network. SAN switching is configured on the switch. The switch fc2/10 NP uplink is shown in the exhibit. Which action ensures that fc2/10 is in an up state?

• A. Replace the SFP port module in fc2/10.
• B. Configure the admin port type E on the upstream switch that connects the port.
• C. Enable NPIV on the upstream switch that connects the port.
• D. Configure the BB_credit buffers on the upstream switch that connects the port.

Answer: C

NEW QUESTION 14
A vPC Type-1 inconsistency between two vPC peers in a VXLAN EVPN setup is discovered. Which two actions need to be attempted to resolve the issue? (Choose two.)

• A. Configure the NVE interfaces to be Up on both switches.
• B. Set a different distributed gateway virtual MAC address.
• C. Set a different secondary IP addresses on NVE source-interface.
• D. Configure the same VNI to multicast group maping.
• E. Set a different primary IP addresses on NVE source-interface.

Answer: AD

NEW QUESTION 15
An engineer is troubleshooting a packet flow from an access leaf to spine. Which EVPN routes are expected on this connection?

• A. EVPN Type 1-5
• B. EVPN Type 0,9,15
• C. EVPN Type 9-15
• D. EVPN Type 0,16

Answer: A

NEW QUESTION 16

Refer to the exhibit. The HSRP instance on both switches is showing as active. Which action resolves the issue?

• A. Configure the HSRP timers to be the same.
• B. Allow VLAN 100 between the switches.
• C. Configure the IP address of N9K-B on the same subnet as N9K-A.
• D. Configure preempt on only one of the switches.

Answer: B

NEW QUESTION 17
After upgrading a client’s fabric interconnect to the latest version, an engineer discovers that the appliance has lost its entire configuration. Which two locations should an engineer check to confirm that the appliance had backed up the configuration prior to the upgrade in order to retrieve the lost configuration? (Choose two.)

• A. Equipment FSM page, InternalBackup stage
• B. Service profiles page, InternalBackup stage
• C. Admin page, PollInternalBackup stage
• D. Equipment FSM page, PollInternalBackup stage
• E. Admin page, InternalBackup stage.

Answer: AC

NEW QUESTION 18
Refer to the exhibit. A network engineer configures an EEM script to get a syslog notification after a configuration change. This message appears when the engineer must make a new configuration to this switch. Which configuration did the engineer neglect to apply in the script for it to function properly?

• A. event cli match ‘configure terminal’
• B. event policy-default count 1 time 100
• C. event syslog occurs 10
• D. action 2.0 event-default

Answer: D

NEW QUESTION 19
A mission-critical server is connected to site A. Connectivity to this server is lost from site B because the MAC route is missing in the OTV VDC of the Nexus 7000 in site B due to MAC aging. Which action allows the flooding of the unknown unicast MAC on the Nexus 7000 in the OTV VDC?

• A. Use route-map to advertise this MAC statically and redistribute with ISIS.
• B. Unknown unicast flooding is not allowed.
• C. Use the otv flood mac <> command to selectively flood traffic for a given MAC.
• D. Use the otv isis bfd <> command to configure BFD protocol.

Answer: B

NEW QUESTION 20
An engineer attempts to register Cisco UCS Manager to Cisco UCS Central, but the registration fails. The engineer can ping Cisco UCS Central from UCS Manager. Which two actions must the engineer attempt to resolve the problem? (Choose two.)

• A. Synchronize the date and time to NTP for Cisco UCS Central and the Cisco UCS domains.
• B. Apply the UCS Central license to UCS Central.
• C. Place Cisco UCS Manager on the same subnet as Cisco UCS Central.
• D. Allow port 443 between Cisco UCS Manager and Cisco UCS Central.
• E. Allow port 9443 between Cisco UCS Manager and Cisco UCS Central.

Answer: AD

NEW QUESTION 21
DRAG DROP
An engineer is troubleshooting issues in Cisco UCS Director. Drag and drop the possible causes from the left onto the correct issues on the right.
Select and Place:

• A. Mastered
• B. Not Mastered

Answer: A

NEW QUESTION 22
......