Introducing The New!
Surepassexam Collection
Get Unlimited Access to all
Surepassexam's PREMIUM files
Q1. OTSPOT
Answer:
Q2. Which command pings from the Cisco Nexus 5548 interface mgmt 0 to host 10.10.1.1?
A. ping -m 10.10.1.1
B. ping 10.10.1.1 -m
C. ping 10.10.1.1 vrf management
D. ping 10.10.1.1 vrf default
Answer: C
Q3. Refer to the exhibit. A network engineer is migrating the existing switching infrastructure to a proposed model. Which technology is enabled on the Cisco Nexus switches to support this migration to its future status?
A. PAgP
B. VSS
C. VPC
D. FCoE
Answer: C
Q4. Which three devices support FCoE? (Choose three.)
A. Cisco Nexus 5500
B. Cisco Nexus 7000
C. Cisco Nexus 3000
D. Cisco Nexus 1000V
E. Cisco UCS Fabric Interconnect
Answer: A,B,E
Q5. On the Cisco Nexus 5000, which three commands help verify network connectivity? (Choose three.)
A. ping
B. show interface brief
C. show otv
D. show vdc membership
E. traceroute
Answer: A,B,E
Q6. Which command issued on the Cisco Nexus 1000V VSM displays the connected VEMs?
A. N1000v-VSM# show vem
B. N1000v-VSM# vem status
C. N1000v-VSM# show module
D. N1000v-VSM# show vem status
E. N1000v-VSM# show vem inventory
Answer: C
Q7. Which three are characteristics of the SAN core-edge design? (Choose three.)
A. few devices to manage
B. deterministic latency
C. lower oversubscription
D. fewer ISLs
E. easy to analyze and tune performance
F. cost-effective for large SANs
Answer: B,E,F
Q8. A network engineer wants to enable a FCoE feature on a Cisco Nexus 5500 Series Switch. When does that occur?
A. after the configuration is saved and rebooted
B. after the configuration is saved
C. after at least one port is configured to operate in FCoE mode
D. after the license is applied
Answer: A
Q9. Which item best describes the STP requirements for Cisco FabricPath?
A. RPVST must be configured on every Cisco FabricPath VLAN.
B. RPVST must be configured on every Cisco FabricPath Border interface.
C. MST must be configured on every Cisco FabricPath VLAN.
D. MST must be configured on every Cisco FPBI.
E. STP is required only to resolve border link failures.
F. STP is not required on Cisco FabricPath interfaces.
Answer: F
Q10. What are two purposes of VIFs in Data Center Unified Fabric? (Choose two.)
A. VIF can be used to virtually present NICs to the operating system
B. VIF is created when interconnecting Catalyst switches to Nexus switches
C. FEX modules can be connected to Nexus parent switches through VIF
D. VIF can be used to directly attach virtual machines with a Unified Computing System
E. VIF creates multiple switch instances inside a VDC
Answer: A,D
Q11. Which ports on the Cisco UCS 6120XP Fabric Interconnects can operate at either 1 Gb/s or 10 Gb/s?
A. Ports 1–4
B. None
C. Ports 1–6
D. Ports 1–8
E. Ports 17–20
Answer: D
Q12. Which is the complementary endpoint to a SCSI target?
A. source
B. origin
C. host endpoint
D. initiator
E. successor
Answer: D
Q13. Where does the data plane operate on a Cisco Nexus 7000 Series Switch?
A. unified crossbar fabric
B. unified port controller
C. supervisor module
D. Policy Feature Card
E. Connectivity Management Processor
Answer: A
Q14. Which three are components of the Cisco Unified Computing System 2104 I/O Module? (Choose three.)
A. multiplexer
B. chassis management console
C. chassis management switch
D. finite state machine
E. chassis management controller
Answer: A,C,E
Q15. Which method of virtualization requires significant modification to the guest operating system?
A. full virtualization
B. paravirtualization
C. partial virtualization
D. hypervisor virtualization
E. host virtualization
F. storage virtualization
G. LAN virtualization
Answer: B
Q16. OTSPOT
Answer:
Q17. A network engineer wants to configure switch ports on Cisco Nexus 2000 and 2200 Fabric Extender switches that are connected to a Cisco Nexus 5500 Series Switch. Which three options allow this configuration? (Choose three.)
A. Connect to each of the Cisco Nexus 2200/2000 switches using Telnet, then configure the FEX switch ports.
B. Connect to a Cisco Nexus 5500 using a console cable, then configure the FEX switch ports.
C. Connect to each of the Cisco Nexus 2200/2000 switches using a console cable, then configure the FEX switch ports.
D. Connect to each of the Cisco Nexus 2200/2000 switches using SSH, then configure the FEX switch ports.
E. Connect to a Cisco Nexus 5500 switch using SSH, then configure the FEX switch ports.
F. Connect to a Cisco Nexus 5500 using Telnet, then configure the FEX switch ports.
Answer: B,E,F