Introducing The New!
Surepassexam Collection
Get Unlimited Access to all
Surepassexam's PREMIUM files
Q1. Which commands can you enter to see if a component in the Cisco UCS domain generated a core file?
A. 6100-A# scope monitoring 6100-A /monitoring # scope sysdebug 6100-A /monitoring/sysdebug # show cores
Core Files: Name Fabric ID
B. 6100-A# scope sysdebug 6100-A /sysdebug # scope monitoring 6100-A /sysdebug/monitoring # show cores
Core Files: Name Fabric ID
C. 6100-A# scope system 6100-A /system # scope monitoring 6100-A /system/monitoring # show cores
Core Files: Name Fabric ID
D. 6100-A# scope cores 6100-A /cores # show cores
Core Files: Name Fabric ID
E. 6100-A# scope logging 6100-A /logging # scope monitoring 6100-A /logging/monitoring # show cores
Core Files: Name Fabric ID
Answer: A
Q2. The Core File Exporter automatically exports cores to a remote server as they are generated. Which protocol does it use for this action?
A. FTP
B. SCP
C. SFTP
D. TFTP
Answer: D
Q3. Which actions on a Cisco UCS Server can be performed under the Cisco IMC utilities? (Choose Four.)
A. export tech support information to a remote host
B. download a tech support file locally
C. reboot the Cisco IMC
D. recover a corrupt BIOS
E. install firmware updates
Answer: ABCD
Q4. The Cisco UCS Manager displays FSM information for which four of these? (Choose four.)
A. which FSM task is being executed
B. the current state of an FSM task
C. the status of the previous FSM task
D. any error codes returned while processing E. all completed FSM tasks
F. multiple FSM tasks that completed over multiple tries
G. multiple FSM tasks that failed
Answer: ABCD
Q5. A customer is trying to boot an operating system installed on a Cisco UCS B-Series blade server after a RAID1 cluster migration. The RAID LUN remains in inactive state during and
after the service profile association and the server does not boot. What is the cause of this problem?
A. RAID1 is not supported in cluster migration mode on a Cisco UCS B-Series blade server.
B. The local disk configuration policy in the service profile on the server is configured with Any Configuration mode rather than RAID1.
C. The server needs to be booted via SAN in cluster migration to support RAID1.
D. The Cisco UCS B-Series blade server has older firmware that needs to be updated first.
Answer: B
Q6. Refer to the exhibit.
Which tab would be the most useful for troubleshooting a blade discovery problem?
A. Faults
B. Events
C. FSM
D. Servers
Answer: C
Q7. Which CLI command identifies the service profile that is associated with a particular compute blade, VIF, vNIC type, link state, and pinned interface?
A. show service-profile path server 1/2
B. show service-profile circuit server 1/2
C. show server-blade circuit server 1/2
D. show server-blade path server 1/2
Answer: B
Q8. As a Cisco UCS administrator, you have a large deployment of C-Series servers. You decide to integrate these into a Cisco UCS Manager environment to simplify management. Which two of these will you need to purchase? (Choose two.)
A. two fabric interconnects
B. a dedicated Cisco IMC
C. two fabric extenders
D. two I/O modules
Answer: AC
Q9. A customer is configuring VSANs in a Cisco UCS domain. After configuring the VSANs 3840, 3841, and 3842 in FC end-host mode, the customer sees that these VSANs are not operational and that Cisco UCS Manager is raising faults. What is the cause of this problem?
A. VSANs 3840, 3841, and 3842 should be in the allowed list on the trunk to clear the fault.
B. VSANs 3840 to 4079 cannot be used in Fibre Channel end-host mode in a Cisco UCS domain.
C. The fabric interconnect needs to be configured in switching mode and the VSANs need to be allowed on the trunk.
D. Use the UCS CLI to clear the fault on the VSAN trunk to forward the VSANs with faults.
Answer: B
Q10. If a server is not associated with a service profile, the activated firmware remains pending. Which two steps should you take? (Choose two.)
A. Manually reboot the server.
B. Reset the server to a new profile.
C. Reset the unassociated server to activate the firmware.
D. Reinitialize the firmware process with Cisco UCS Manager.
E. Download the firmware and start over.
F. Shut down gracefully and start over.
Answer: AC
Q11. Which of these does not have an FSM associated with it?
A. vCenter connection
B. service profile
C. server hardware
D. service profile templates
Answer: D
Q12. When a service profile is disassociated from a server, what happens to the identity and connectivity information for the server?
A. It is cleared and set to the default that was setup initially by the first configuration.
B. It is maintained and can be reused.
C. It is reset to factory defaults.
D. It uses master service profile parameters.
E. It takes parameters of other servers in the service profile.
Answer: C
Q13. How does the FSM react after an error or timeout at a stage?
A. stops
B. retries until successful
C. continues
D. retries that stage at scheduled intervals
E. raises faults and continues
Answer: D
Q14. Which of these is a supported Cisco C-Series integration topology?
A)
B)
C)
D)
A. Exhibit A
B. Exhibit B
C. Exhibit C
D. Exhibit D
Answer: B
Q15. Which statement is true about system event logs?
A. By default, they require manual clearing.
B. They report operating system crashes and errors.
C. They are also referred to as system error logs.
D. They can only be accessed from Cisco UCS Manager.
Answer: A
Q16. Which piece of information does the FSM provide?
A. the current task and status
B. a collection of blade statistics
C. the last user to access the resource
D. a list of faults currently suppressed by the Cisco UCS Manager
Answer: A
Q17. You are troubleshooting an FCoE boot issue on a Cisco UCS C220 M3 server with a VIC 1225 CNA. Which two pieces of information can you directly infer from the output of the show zone active command below? (Choose two.)
zone name Server_1-to-Storage vsan 11
pwwn 50:06:01:60:3b:a0:08:9f [Storage]
*fcid 0x3b000b [pwwn 20:00:00:25:b5:04:0a:02] [C22_Server]
A. The storage controller is not logged into the fabric.
B. The server is not logged into the fabric.
C. Only the storage controller is logged into the fabric.
D. Only the server is logged into the fabric.
E. The initiator and target cannot communicate because they are on the wrong VSAN.
F. The WWPN of the storage controller is mistyped.
G. The initiator and target cannot communicate because the zone name does not match the server name (C22_Server).
Answer: AD
Q18. A customer is trying to boot an operating system that is installed on the eUSB on a Cisco UCS B-Series blade server; however, the boot fails. What is the cause of this failure?
A. The local disk must be the first device in the boot order.
B. eUSB is not a supported boot device.
C. eUSB support is available only on the Cisco UCS C-Series rack server.
D. eUSB is not the first device in the boot order for the server.
Answer: D
Q19. What should you do when you see faults during the initial setup and discovery process?
A. Take note and address the faults.
B. You can safely ignore these faults.
C. Log them and try to address the first one.
D. Reboot until the error messages go away.
Answer: B
Q20. Which CLI command will indicate whether a Cisco UCS C-Series rack-mount server has any failed DIMMs?
A. ucs-c250 / # scope chassis ucs-c250 /chassis # show dimm-summary
B. ucs-c250 / # scope chassis ucs-c250 /chassis # show dimm-fault C. ucs-c250 / # scope chassis ucs-c250 /chassis # show dimm-ecc
D. ucs-c250 / # scope chassis ucs-c250 /chassis # show dimm-recovery
Answer: A
Q21. A Cisco UCS chassis has two ports on I/O Module 1 connected to Fabric Interconnect A, and two ports on I/O Module 2 connected to Fabric Interconnect B. The I/O modules are connected to ports 1 and 2 on their respective fabric interconnects, and end host mode is configured. After a link failure occurs on port 1 of I/O Module 1, what happens to the traffic that was pinned to that link?
A. The traffic fails until the link issue is resolved.
B. The traffic is repinned to I/O Module 2 link 1, which is connected to Fabric Interconnect
C. The traffic is repinned to the remaining link between I/O Module 1 and Fabric Interconnect A.
D. The traffic is repinned automatically to Fabric Interconnect B.
Answer: C