Introducing The New!
Surepassexam Collection
Get Unlimited Access to all
Surepassexam's PREMIUM files
Q1. A Cisco Nexus 2000 Series Fabric Extender is connected to two Cisco Nexus 5000 Series switches via a vPC link. After both Cisco Nexus 5000 Series switches lose power, only one switch is able to power back up. At this time, the Cisco Nexus 2000 Series Fabric Extender is not active and the vPC ports are unavailable to the network.
Which action will get the Cisco Nexus 2000 Series Fabric Extender active when only one Cisco Nexus 5000 Series switch is up and active?
A. Move the line from the failed Cisco Nexus 5000 Series switch to the switch that is powered on, so the port channel forms automatically on the switch that is powered on.
B. Shut down the peer link on the Cisco Nexus 5000 Series switch that is powered on.
C. Configure reload restore or auto-recovery reload-delay on the Cisco Nexus 5000 Series switch that is powered on.
D. Power off and on the Cisco Nexus 2000 Series Fabric Extender so that it can detect only one Cisco Nexus 5000 Series switch at power up.
Answer: C
Q2.
What is the status of FC interface associated with ethernet 1/5 indicate?
A. Trunk VSAN 11 is isolated B. Inteface vfc 5 is up and running for the assigned VSAN
C. Trunk VSAN 11 is intializing
D. VSAN to FC mapping is not working as expected
Answer: B
Q3.
What is effect of the command fabricpath load-balance unicast Iayer3"?
A. It configures F2 VDC FabricPath unicast load balancing
B. The command automatically load balances broadcast traffic
C. It configures F1/MI VDC FabricPath unicast load balancing
D. It configures M1 VDC FabricPath unicast load balancing
Answer: C
Q4. Which topology is not supported when using vPC?
A. a single-homed server to a single FEX that is connected to two Cisco Nexus 5500 Series Switches
B. a dual-homed server to two FEXs, each connected to two Cisco Nexus 5500 Series Switches
C. a dual-homed server to two FEXs that are connected to one Cisco Nexus 5500 Series Switch
D. a dual-homed server to a single FEX that is connected to two Cisco Nexus 5500 Series Switches
Answer: C
Q5. Which statement about Cisco FabricPath is true?
A. It is the best solution for interconnecting multiple data centers.
B. It optimizes STP throughout the Layer 2 network.
C. It is a simplified extension of Layer 3 networks across a single data center.
D. The Cisco FabricPath domain appears as a single STP bridge, where each edge port uses the same MAC address.
Answer: D
Q6. Which statement is true if password-strength checking is enabled?
A. Short, easy-to-decipher passwords will be rejected.
B. The strength of existing passwords will be checked.
C. Special characters, such as the dollar sign ($) or the percent sign (%), will not be allowed.
D. Passwords become case-sensitive.
Answer: A
15. Which statement about RBAC user roles on a Cisco Nexus switch is true?
A. If you belong to multiple roles, you can execute only the commands that are permitted by both roles (logical AND).
B. Access to a command takes priority over being denied access to a command.
C. The predefined roles can only be changed by the network administrator (superuser).
D. The default SAN administrator role restricts configuration to Fibre Channel interfaces.
E. On a Cisco Nexus 7000 Series Switch, roles are shared between VDCs.
Q7. After enabling strong, reversible 128-bit Advanced Encryption Standard password type-6 encryption on a Cisco Nexus 7000, which command would convert existing plain or weakly encrypted passwords to type-6 encrypted passwords?
A. switch# key config-key ascii
B. switch(config)# feature password encryption aes
C. switch# encryption re-encrypt obfuscated
D. switch# encryption decrypt type6
Answer: C
Q8. Between which two types of ports does FIP establish Fibre Channel virtual links? (Choose two.)
A. VE Ports and VE Ports
B. N Ports and F Ports
C. VN Ports and VF Ports
D. VP Ports and VE Ports
E. VE Ports and VF Ports
F. E Ports and E Ports
Answer: AC
Q9. Which three items must be configured in the port profile client in Cisco UCS Manager? (Choose three.)
A. port profile
B. DVS
C. data center
D. folder
E. vCenter IP address
F. VM port group
Answer: BCD
Q10. What is the Overlay Transport Virtualization site VLAN used for?
A. to allow the join interfaces at different sites to communicate
B. to detect devices at the site that are not capable of OTV
C. to allow multiple site AEDs to communicate with each other
D. to detect other OTV edge devices in the site
Answer: D
Q11. Which SCSI terminology is used to describe source and destination nodes?
A. hosts and targets
B. initiators and targets
C. HBA and disks
D. initiators and disks
E. HBA and targets
Answer: B
Q12. In policy-based routing, which action is taken for packets that do not match any of the route-map statements?
A. forwarded after the egress queue empties on the outbound interface
B. forwarded using the last statement in the route map
C. forwarded using the closest matching route-map statement
D. forwarded using destination-based routing
Answer: D
Q13. Which statement about enhanced zoning on Cisco Multilayer Director Switches are true?
A. It allows partial zone set changes to be distributed without having to activate a zone set.
B. Enhanced zoning is compatible with IVR.
C. Zone changes can scheduled with a CRON job.
D. More than one zone set can be active with enhanced zoning.
Answer: A
Q14. Which statement about implementation of Cisco TrustSec on Cisco Nexus 5546 or 5548 switches are true?
A. Cisco TrustSec support varies depending on Cisco Nexus 5500 Series Switch model.
B. The hardware is not able to support MACsec switch-port-level encryption based on IEEE 802.1AE.
C. The maximum number of RBACL TCAM user configurable entries is 128k.
D. The SGT Exchange Protocol must use the management (mgmt 0) interface.
Answer: B
Q15. Which command enables NPIV on Cisco Nexus 5000 Series Switches and Cisco MDS switches?
A. switch(config)# npiv enable
B. switch(config)# npivon
C. switch(config)# feature npiv
D. switch(config)# npiv proxy
E. switch(config)# np proxy-enable
Answer: C
Q16. Which function does the graceful restart feature allow a Cisco Nexus 7000 Series router to perform?
A. Perform a rapid route convergence.
B. Initialize a standby supervisor transparently when one is present.
C. Remain in the data forwarding path through a process restart.
D. Maintain a management connection throughout a router restart.
Answer: C