Avaya 7003 Free Practice Questions

Question No: 4

A customer has a several analog telephones running of a Flexible Analog Line Card (FALC) in an IPMG. Users are able to receive calls on the telephone and have a conversation, however they cannot initiate a call as there is no dial tone.

What should be checked first?

A. Tone and digital loops (TDS), extended tone detector (XTD)

B. Physical connections, dsp resource availability, and tone loops

C. All tone and digit switch loops (TDS), IPMG registration status

D. All XTD and conference loops

View Answer

Question No: 5

A customer is commissioning a Communication Server (CS) 1000E 7x system with package 403 (soft switch) and 402 (IPMG). The CPDC Call Server software has been installed successfully, and now the customer is provisioning the Media Gateway Tone and conference loops for the Media Gateway Controller.

Which switch overlay and prompt should the customer use to configure the Media gateway TDS loop?

A. LD 17, XCT

B. LD 17, VXCT

C. LD 17, SUPT

D. LD 17, MGTDS

View Answer

Question No: 6

Click the Exhibit button.

A technician is performing an upgrade of existing Communication Server 1000E Rls. 6.0 servers from the Deployment Servers. The system is pre-configured and the status is un- deployed. The server has been selected, but the Deployment Actions pull-down list does not include the choice to deploy.

Which two corrective actions must be taken to continue with deployment? (Choose two)

A. Click the radio button associated with the server

B. Click the Disable NFS button

C. Click the Commit button

D. Click the add Linux Server button

View Answer

Question No: 7

A technician is planning to upgrade a customeru2021s existing Communication Server 1000E Rls. 6.0 system. During the upgrade, a CPPM server card from storage will be added to provide an additional signaling server.

Which two statements describes what must be done to the CPPM server card to distinguished it as a signaling Server (Choose two)

A. Set switch 5 to position 1.

B. Set switch 5 to position 2.

C. Install one Compact Flash Drive (RMD) and one Hard Drive (FMD)

D. Install one Compact Flash Drives (one RMD and one FMD)

View Answer

Question No: 8

A customer with an existing Option 11C Rls. 5.5 chassis system plans to upgrade to a Communication Server (CS) 1000E Rls. 7x Standard Availability with a single IP Media Gateway (MG) 1000E chassis.

To complete the upgrade, which component in the Option 11C must be replaced?

A. SSC Card

B. Call Processor

C. Media Gateway

D. Digital Line Card

View Answer

Question No: 9

A customer is implementing a Communication Server 1000E (CS 1000E) Rls. 7x High Availability (HA) system. The customer wants to know if there are any special package requirements beyond the HA Package needed for the system.

Which two software packages are mandatory when deploying a CS 1000E system? (Choose two)

A. IPMG u2013 Media gateway 1000E package 403

B. SOFTSWITCH-Soft Switch Package 402

C. SBO u2013 Branch Office Package 390

D. SIP u2013 SIP Gateway and Converged Desktop Package 406

View Answer

Question No: 10

A technician has configured a new media gateway by connecting to the serial port for the MGC and entering network information for the card as well as the IP address for the Primary call server. When the MGC reboots, the faceplates displays UNRG. The Call Server console u2021IPMG registration deniedu2021.

What should be done to solve this problem?

A. Ping from the MGC to the call server over the E-LAN

B. Check to ensure the TLAN cable for the MGC is connected and active

C. Check to ensure the IPMG has been configured on the call server

D. Power cycle the MGC card to force it to register

View Answer

Question No: 11

A customer has installed a Media gateway controller (MGC) and would like to change the baud rate settings for the SDI parts. The baud rates for all serial Data Interface (SDI) ports on the MGC are configurable through call server?

Which overlay is used to configure the MGC SDI ports?

A. LD 137

B. LD 117

C. LD 97

D. LD 17

View Answer

Question No: 12

A field calls about a problem enabling the DSPs on a new Communication Server (CS) 1000E SA Co-resident on release 7x. The DSPs on the MG 1 are all enabled but enabling the DSPs on MG2 and MG3 fail, and asked that the configuration be reviewed.

MG1: CPMG 128

MG2: MGC 128 DSP DB in position 2

MG3: MGC 128 DSP DB in position 2

After reviewing the configuration, an error in the DSP 128 VGW (DSP) configuration is identified?

Which configuration option accurately reflects the proper configuration for the voice Gateway (DSP) channel?

A. Numbering of VGW channels: 128 Trunk data block VGW

Terminal number: 004 0 02 0 Designator field for trunk: DSP Extended trunk DSP DB 128 Customer number: 00

B. Numbering of VGW channels: 128 Trunk data block VGW

Terminal number: 004 0 01 0 Designator field for trunk: DSP Extended trunk DSP DB 128 Customer number: 00

C. Numbering of VGW channels: 128 Trunk data block VGW

Terminal number: 004 0 00 0 Designator field for trunk: DSP Extended trunk DSP DB 128

Customer number: 00

D. Numbering of VGW channels: 128 Trunk data block VGW

Terminal number: 004 0 11 0 Designator field for trunk: DSP Extended trunk DSP DB 128 Customer number: 00

View Answer

Question No: 13

A customer with a Communication Server (CS) 1000E at Rls. 5.5 with two IPMG is upgrading the system to CS 1000E SA release 7 x. The second media gateway includes a media Gateway Controller card with one high density DSP daughter board.

How many voice channels does this configuration provide?

A. 32

B. 64

C. 96

D. 128

View Answer