Introducing The New!
Surepassexam Collection
Get Unlimited Access to all
Surepassexam's PREMIUM files
Q1. - (Topic 1)
A DLPAR memory operation was attempted and failed. Given the following information, what is the likely caused
A. Source LPAR is using all of its allocated memory
B. Operation timed out
C. Destination LPAR maximum memory setting is too low.
D. HMC RMC daemons are not communicating properly to the source
E. Source LPAR minimum memory setting is too high.
F. Source LPAR maximum memory setting is too low.
Answer: C
Q2. - (Topic 3)
Where is the file size limit for all users defined?
A. /etc/security/environ
B. /etc/security/limits
C. /etc/security/environments
D. /etc/environment
Answer: B
Q3. - (Topic 1)
Which of the following is an AIX 7 Cluster Aware feature?
A. Cluster application load balancing
B. Cluster shared volume groups on the shared disk C. Cluster IP addresses on the shared resource
D. Cluster configurations on the cluster repository disk
Answer: D
Q4. - (Topic 4)
Which of the following is a supported source for creating a Versioned WPAR?
A. An existing AIX 5.2 mksysb
B. AIX 5.3 base product media
C. An AIX 6.1 Global Environment
D. NIM AIX 5.3 lpp_source and spot
Answer: A
Q5. - (Topic 4)
An LPAR is hosted on Power8 hardware.
How can an adapter assigned as “required” to that LPAR be removed with minimal downtime?
A. Initiate the Add/Remove procedure from the ASMI
B. Use the CHARM tool to remove the adapter
C. Remove the device throughdiag,and DLPAR remove the adapter
D. Remove the required setting in the profile, and DLPAR remove the adapter
Answer: D
Q6. - (Topic 2)
In order to enable an AIX host to use one virtual Ethernet adapter to communicate on multiple VLANs, what is required?
A. The VLAN devices used by the host must be configured with IP addresses on different subnets.
B. The virtual Ethernet adapter must be set to full duplex in AIX.
C. VLAN devices must be configured in the AIX host.
D. The virtual Ethernet adapter must be configured as a trunk adapter.
Answer: C
Q7. - (Topic 4)
What is the purpose of using relative path names when creating a tar file?
A. To allow the tar file to be used on Linux systems
B. To ensure files are always extracted to a specific path
C. To restore to a raw device name on the destination system
D. To enable restored files to be extracted to any user-specified location
Answer: D
Q8. - (Topic 1)
An LPAR is configured with strict logical volume mirroring across two disks for resilience. The administrator would like to ensure if one disk fails the volume group stays online. Which command will ensure that the datavg volume group stays online?
A. varyonvg -n datavg
B. mirrorvg-Q-c 2 datavg
C. mklvcopy -e m -s y (each logical volume name) 2
D. chvg -Qn datavg
Answer: D
Q9. - (Topic 2)
The AIX hosts node1 and node2 have Ethernet adapters, both named ent0, configured on the same network. Both are dedicated physical 1GB adapter ports in a Host Ethernet
Adapter. Based on this information and the output shown for each node, what is the most likely cause of intermittent failures and slow communication between these adapters?
A. The jumbo_frarnes setting is 'no' and should be set to 'yes'.
B. The Multi-Core Scaling mode is enabled. Multi-Core Scaling is interfering with communications because the processor is too busy.
C. The Shared Ethernet Adapter does not have enough bandwidth to accommodate the network traffic.
D. The media speed is set differently on the adapters than the endpoints on the switch.
Answer: D
Q10. - (Topic 4)
A customer has a virtualized system using Virtual I/O Server with multiple client partitions accessing the SAN using NPIV?
Which command on the client partition should be run to retrieve the network address of the fiber adapter?
A. lscfg -vp –l fcs0
B. lspci –va fcsi | grep “Network Address”
C. lspath –npiv fcs0 | grep “NetworkAddress”
D. lsdev | grep fcs0
Answer: C
Q11. - (Topic 1)
What are key considerations when planning for Live Application Mobility?
A. The WPAR is an Application WPAR and both global environments are at the same AIX level
B. That theWPAR is checkpointable and both global environments are on the same subnet
C. The NFS services are running and applications are stopped
D. The NFS services are running and there is an HMC attached to both managed systems
Answer: B
Q12. - (Topic 3)
An administrator is required to create a System WPAR and configure it for mobility, which command will do this?
A. mkwpar-c wparname
B. mkwpar-m wparname
C. crwpar-c wparname
D. crwpar-m waprname
Answer: A
Q13. - (Topic 2)
Which system management tool could be used to deploy corrective service to multiple HMCs?
A. Distributed Systems Manager
B. Network Installation Manager
C. IBM Systems Director
D. Cluster Systems Manager
Answer: C
Q14. - (Topic 2)
A server on the 165.x.x.x subnetis displaying network problems. The administrator uses a console connection and gathers the following information:
Which action will permanently resolve the issue?
A. Flush the routing table.
B. Run 'route del 10.2.98.113-f.
C. Modify/etc/routes and reboot the system.
D. Run 'chdev-I inet0-a delroute=net.-hopcount,0,,0.10.2.98.113'.
Answer: D
Q15. - (Topic 2)
An administrator has been asked to consolidate disks on an LPAR. Given the following information, which group of actions will remove unneeded disk?
A. Migrate physical partitions from hdisk2 to hdisk3 Remove hdisk2 from datavg Use rmdevto permanently remove hdisk3
B. Remove hdi sk3 from datavg Use rmdevto permanently remove hdisk3
C. Export datavg Use rmdevto permanently remove hdisk3 re-import db2vg03
D. Vary off datavg Use rmdevto permanently remove hdisk3 varyonvg dbvg02
Answer: B
Q16. - (Topic 4)
When preparing to install a System WPAR using NIM, what action must occur before the planned WPAR can be successfully defined as a NIM client?
A. Install AIX onto the global environment.
B. Register the planned hostnamesto DNS.
C. Define the global environment LPAR as a NIM client.
D. Create an lpp_source with the WPAR-specific backup files.
Answer: C