Introducing The New!
Surepassexam Collection
Get Unlimited Access to all
Surepassexam's PREMIUM files
Q1. - (Topic 1)
How is the FortiGate password recovery process?
A. Interrupt boot sequence, modify the boot registry and reboot. After changing the password, reset the boot registry.
B. Log in through the console port using the “maintainer” account within several seconds of physically power cycling the FortiGate.
C. Hold down the CTRL + Esc (Escape) keys during reboot, then reset the admin password.
D. Interrupt the boot sequence and restore a configuration file for which the password has
been modified.
Answer: B
Q2. - (Topic 11)
A static route is configured for a FortiGate unit from the CLI using the following commands: config router static edit 1 set device "wan1" set distance 20 set gateway 192.168.100.1 next end Which of the following conditions are required for this static default route to be displayed in
the FortiGate unit’s routing table? (Choose two.)
A. The administrative status of the wan1 interface is displayed as down.
B. The link status of the wan1 interface is displayed as up.
C. All other default routes should have a lower distance.
D. The wan1 interface address and gateway address are on the same subnet.
Answer: B,D
Q3. - (Topic 14)
An administrator has formed a high availability cluster involving two FortiGate units.
[ Multiple upstream Layer 2 switches] -- [ FortiGate HA Cluster ] -- [ Multiple downstream Layer 2 switches ]
The administrator wishes to ensure that a single link failure will have minimal impact upon the overall throughput of traffic through this cluster.
Which of the following options describes the best step the administrator can take?
The administrator should _____________________.
A. Increase the number of FortiGate units in the cluster and configure HA in active-active mode.
B. Enable monitoring of all active interfaces.
C. Set up a full-mesh design which uses redundant interfaces.
D. Configure the HA ping server feature to allow for HA failover in the event that a path is disrupted.
Answer: C
Q4. - (Topic 11)
Review the output of the command get router info routing-table database shown in the exhibit below; then answer the question following it.
Which two statements are correct regarding this output? (Choose two.)
A. There will be six routes in the routing table.
B. There will be seven routes in the routing table.
C. There will be two default routes in the routing table.
D. There will be two routes for the 10.0.2.0/24 subnet in the routing table.
Answer: A,C
Q5. - (Topic 5)
Which two statements are true about IPsec VPNs and SSL VPNs? (Choose two.)
A. SSL VPN creates a HTTPS connection. IPsec does not.
B. Both SSL VPNs and IPsec VPNs are standard protocols.
C. Either a SSL VPN or an IPsec VPN can be established between two FortiGate devices.
D. Either a SSL VPN or an IPsec VPN can be established between an end-user workstation and a FortiGate device.
Answer: A,D
Q6. - (Topic 15)
Which IPsec mode includes the peer id information in the first packet?
A. Main mode.
B. Quick mode.
C. Aggressive mode.
D. IKEv2 mode.
Answer: C
Q7. - (Topic 17)
Which statement is one disadvantage of using FSSO NetAPI polling mode over FSSO Security Event Log (WinSecLog) polling mode?
A. It requires a DC agent installed in some of the Windows DC.
B. It runs slower.
C. It might miss some logon events.
D. It requires access to a DNS server for workstation name resolution.
Answer: C
Q8. - (Topic 1)
When creating FortiGate administrative users, which configuration objects specify the account rights?
A. Remote access profiles.
B. User groups.
C. Administrator profiles.
D. Local-in policies.
Answer: C
Q9. - (Topic 15)
Review the IPsec phase 2 configuration shown in the exhibit; then answer the question below.
Which statements are correct regarding this configuration? (Choose two.).
A. The Phase 2 will re-key even if there is no traffic.
B. There will be a DH exchange for each re-key.
C. The sequence number of ESP packets received from the peer will not be checked.
D. Quick mode selectors will default to those used in the firewall policy.
Answer: A,B
Q10. - (Topic 10)
Which statements are correct regarding application control? (Choose two.)
A. It is based on the IPS engine.
B. It is based on the AV engine.
C. It can be applied to SSL encrypted traffic.
D. Application control cannot be applied to SSL encrypted traffic.
Answer: A,C
Q11. - (Topic 7)
Which statement is correct regarding virus scanning on a FortiGate unit?
A. Virus scanning is enabled by default.
B. Fortinet customer support enables virus scanning remotely for you.
C. Virus scanning must be enabled in a security profile, which must be applied to a firewall policy.
D. Enabling virus scanning in a security profile enables virus protection for all traffic flowing through the FortiGate.
Answer: C
Q12. - (Topic 2)
Which is an advantage of using SNMP v3 instead of SNMP v1/v2 when querying a FortiGate unit?
A. MIB-based report uploads.
B. SNMP access limited by access lists.
C. Packet encryption.
D. Running SNMP service on a non-standard port is possible.
Answer: C
Q13. - (Topic 2)
What is the maximum number of FortiAnalyzer/FortiManager devices a FortiGate unit can be configured to send logs to?
A. 1
B. 2
C. 3
D. 4
Answer: C
Q14. - (Topic 6)
Which IPsec configuration mode can be used for implementing GRE-over-IPsec VPNs?.
A. Policy-based only.
B. Route-based only.
C. Either policy-based or route-based VPN.
D. GRE-based only.
Answer: B
Q15. - (Topic 22)
Which statements are true about offloading antivirus inspection to a Security Processor (SP)? (Choose two.)
A. Both proxy-based and flow-based inspection are supported.
B. A replacement message cannot be presented to users when a virus has been detected.
C. It saves CPU resources.
D. The ingress and egress interfaces can be in different SPs.
Answer: B,C
Q16. - (Topic 6)
An administrator wants to create an IPsec VPN tunnel between two FortiGate devices.
Which three configuration steps must be performed on both units to support this scenario? (Choose three.)
A. Create firewall policies to allow and control traffic between the source and destination IP addresses.
B. Configure the appropriate user groups to allow users access to the tunnel.
C. Set the operating mode to IPsec VPN mode.
D. Define the phase 2 parameters.
E. Define the Phase 1 parameters.
Answer: A,D,E